Pioneer S-STP600 운영 지침 - 페이지 3
{카테고리_이름} Pioneer S-STP600에 대한 운영 지침을 온라인으로 검색하거나 PDF를 다운로드하세요. Pioneer S-STP600 4 페이지. Speaker system
페이지 인쇄
Non-skid pads
Attach the non-skid pads to the base of the speakers. Use the
supplied adhesive to attach 4 pads to the base (flat surface) of each
speaker.
Cabinet maintenance
Use a polishing cloth or dry cloth to wipe off dust and dirt.
If the cabinet is very dirty, clean with a soft cloth dipped in some
neutral cleanser diluted five or six times with water, and then wipe
again with a dry cloth. Do not use furniture wax or cleaners.
Never use thinners, benzene, insecticide sprays and other
chemicals on or near the cabinets, since these will corrode the
surfaces.
Wall-mounting the front and surround speaker
system
Attaching the brackets
• Make sure to tighten the supplied screw as securely as possible
when attaching the bracket to the back of the speaker.
• Please do not attach the brackets to the center speaker.
Before mounting
• Remember that the speaker system is heavy and that its weight
could cause the wood screws to work loose, or the wall material
to fail to support it, resulting in the speaker falling. Make sure
that the wall on which you intend to mount the speakers is
strong enough to support them. Do not mount on plywood or
soft surface walls.
• Mounting screws are not supplied. Use screws that are suitable
for the wall material and that will support the weight of the
speaker.
Note
• If you are unsure of the qualities and strength of the walls,
consult a professional for advice.
• Pioneer is not responsible for any accidents or damage that
result from improper installation.
Bracket screw
(supplied)
Mounting screw
(not supplied)
5 – 7 mm
Troubleshooting
Symptom
No sound
Sound is
distorted
Speakers stop
producing
sound suddenly
• These speakers are equipped with a protection device to protect
the transducers from extreme conditions. Under these
conditions the protection device will activate and stop the
speaker from producing sound. If this happens turn the volume
down to resume normal speaker output.
Specifications
Front / Surround / Surround back speakers
Enclosure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Closed-box bookshelf type
System. . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.7 cm 1-way system Speakers
Speaker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7.7 cm cone type
Nominal impedance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Ω Ω Ω Ω
Frequency range. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85 Hz to 20 kHz
Dimensions. . . . . . . . . . . . . . . . . . . . . . . .105 (W) x 115 (H) x 114 (D) mm
Weight
Front speakers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.6 kg
Surround speakers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.66 kg
Surround back speaker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.66 kg
Center speaker
Enclosure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Closed-box bookshelf type
System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7.7 cm 1-way system
Speaker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7.7 cm cone type
Nominal impedance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Ω Ω Ω Ω
Frequency range. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80 Hz to 20 kHz
Dimensions. . . . . . . . . . . . . . . . . . . . . . . . .270 (W) x 90 (H) x 100 (D) mm
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.8 kg
Note: Specifications and design subject to possible modification
without notice due to improvements.
5 mm
10 mm
Possible cause
• Bad speaker wire or
connection
• Receiver is off
• Volume control is at
zero
• Extreme signal
condition
• Extreme signal
condition for extended
period of time
Caution
Remedy
• Connect correctly or
replace wire.
• Turn on receiver.
• Slowly turn up volume.
• Turn down the
amplifier's output level
(volume, bass control,
bass boost) to lower the
level.
• Turn the volume down
to resume normal
speaker output.
(magnetically shielded)
(magnetically shielded)