Pioneer S-VSL3 운영 지침 - 페이지 3

{카테고리_이름} Pioneer S-VSL3에 대한 운영 지침을 온라인으로 검색하거나 PDF를 다운로드하세요. Pioneer S-VSL3 4 페이지. Pioneer s-vsl3: operating instruction

페이지 인쇄

•

The most natural listening experience will be produced when the

listening position is midway between and an equal distance from

the two speakers, as shown. Adjust the speaker wire to the same

length from both speakers.

Adjusting the Bass Range

This speaker system is supplied with acoustic control material

which can be affixed to the bottom of the stand as a means of

adjusting the bass frequency range. Apply the material as shown,

in accordance with your installation location and personal

listening tastes.

Acoustic control material

Apply acoustic control material

sheet to the bottom surface of the

speaker system stand. Take care

not to allow the sheet to come

between the small skid-pads and

floor.

•

When using the speakers in a room with permeable walls, place

the speakers as closely as possible along the walls or install them

in front of a screen or other object with reflective properties.

•

When used with a television, the speakers should be installed so

that their front surfaces are in the same plane as the screen of the

television.

•

When using the speakers with a television screen, the optimum

breadth of sound will be produced when the television screen is

placed midway between the right and left speakers and the

speakers are oriented at angles of about 50–60° from the listening

position.

•

In rooms with hard reflective or resonating walls it may be

desirable to cover the walls with a curtain and/or place a carpet on

the floor to dampen excessive sound reflection. Extending the

curtain all the way to the corners will help prevent local deadening

of the sound. On the other hand if the wall opposite the speakers

(behind the listening position) is also composed of a hard surface,

placing a thick curtain over the wall will help prevent the

production of standing waves and result in better sound.

Installation Precautions

•

These speaker systems are heavy; installing them in unstable

locations is extremely dangerous and should be avoided.

Connection to Amplifier

Terminals are provided at the bottom of the speakers for connection

to an amplifier.

1 Disconnect the power cord to the amplifier.

2 Connect the speaker wires to the input terminals at the bottom of

the speakers to the amplifier's speaker output terminals.

Connect the hot-side speaker wire to the + speaker output

terminal; connect the common-side speaker wire to the - speaker

output terminal.

IM-S-VSL3-new.p65

1. Remove insulation at end of wire and twist ends of

wire strands.

2. Insert speaker wire through hole in the bottom of the

speaker stand.

3. Loosen the screws, pass the wire cores through the

terminal holes and retighten thoroughly.

Black -

Connect the common-side

speaker wire to the - speaker

output terminal.

4. Remove the protective backing paper from the hook-

and-loop fastener strip (hook strip), and apply to the

bottom of the speaker stand near the rim depression

for the speaker wire (see illustration).

5. Pass the speaker wire through the rim depression as

shown.

6. Place the other hook-and-loop fastener strip (loop

strip) onto the first strip (hook) with the speaker wire

passing between the two strips, so as to fix the

speaker wire in position.

Rim depression

Hook-and-loop

for speaker

wire.

fastener strip

(loop)

Place loop

strip over

wire and

onto hook

strip

•

After connecting the wires to terminals, pull gently on the wire and

confirm that the wire lead is fastened securely to its terminal.

Insecure connections will result in distorted sound and noise.

•

Do not allow bare wire ends to protrude excessively from the

terminals. If the bare wires from the two leads touch each other

excessive load will be placed on the amplifier leading to possible

damage or malfunction.

•

Be sure to connect the + and – leads to their correct terminals. If

the poles at one end of the wires are connected mistakenly (+ to –

, – to +), proper stereo effect will not be produced.

3/22/2004, 4:35 PM

Red +

Connect the hot-side

speaker wire to the +

speaker output

terminal.

Hook-and-loop

fastener strip (hook)