Pioneer S-W3700 운영 매뉴얼 - 페이지 3

{카테고리_이름} Pioneer S-W3700에 대한 운영 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Pioneer S-W3700 11 페이지. Speaker system
Pioneer S-W3700에 대해서도 마찬가지입니다: 서비스 매뉴얼 (3 페이지)

페이지 인쇄

Assembling the speaker stand bases and securing

your front and surround (S-FCR4700 only)

speakers

Attach the speaker stand bases to the stems using the screws

provided.

Once you have aligned the stem and base, secure with the small

screws at the points shown below. Note that the speaker should

face in the direction of the base of the isosceles triangle (outlined

below).

Rear

Front

Secure each of the front and surround (S-FCR4700 only)

speakers using the plastic catch provided.

Screw two picture hooks or similar into the wall behind the

speaker. Pass a cord around the hooks and through the plastic

catch so that the speaker is stabilized (make sure to test that it

supports the weight of the speaker).

After installing, make sure the speaker is securely fixed.

CAUTION:

• The plastic catch is not a mounting fixture, and the speaker

should not be hung directly from the wall using this catch.

Always use a cord when stabilizing the speaker.

• Pioneer disclaims all responsibility for any losses or

damage resulting from improper assembly, installation,

insufficient strength of the installation materials, misuse,

or natural disasters.

NON-SKID PADS

Attach the small non-skid pads to the base of the surround (S-

FCR3700 only) and center speakers. The large non-skid pads

are for the front and surround (S-FCR4700 only) speakers, and

the subwoofer (as shown).

Use the adhesive side of the pads to attach them to the base of

each speaker and the subwoofer.

If you choose to use speaker stands with the surround speakers,

attach the non-skid pads to the stand bases instead of to the

underside of the speakers (S-FCR3700 only).

Sufficiently thick

cord (not supplied)

Plastic catch

Small non-skid pads

Center speaker

Surround speakers

(S-FCR3700 only)

Large non-skid pads

Front and Surround

(S-FCR4700 only) speakers

OPTIONALLY, ATTACH THE SURROUND SPEAKERS

TO THE SPEAKER STANDS (S-FCR3700 ONLY)

For each speaker,line up the spurs on the stand with the holes

on the back of the speaker and insert, then secure the speaker

to the stand with the screw provided.

WALL MOUNTING THE SURROUND (S-

FCR3700 ONLY) AND CENTER SPEAKERS

The surround (S-FCR3700 only) and center speakers have

mounting holes which can be used to mount the speaker on the

wall.

Mounting screw

(not supplied)

3/16 in. to 1/4 in.

(5 mm to 7 mm)

Before mounting (see above), keep in mind the following points:

• Remember that the speaker system is heavy and that its weight

could cause the screws to work loose, or the wall material to

fail to support it, resulting in the speaker falling.

Make sure that the wall you intend to mount the speakers on

is strong enough to support them. Do not mount on plywood

or soft surface walls.

• Mounting screws are not supplied. Use screws suitable for

the wall material and support the weight of the speaker.

CAUTION:

• If you are unsure of the qualities and strength of the walls,

consult a professional for advice.

• Pioneer is not responsible for any accidents or damage

that result from improper installation.

Speaker stands

(S-FCR3700 only)

Subwoofer

3/16 in.

(5 mm)

3/8 in.

(10 mm)