Pioneer XY-81 사용자 설명서 - 페이지 6

{카테고리_이름} Pioneer XY-81에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Pioneer XY-81 12 페이지. 8″ two way
Pioneer XY-81에 대해서도 마찬가지입니다: 사용자 설명서 (12 페이지)

페이지 인쇄

System set-up

WARNING

! Loudspeaker systems are potentially dangerous objects if used incorrectly. Please ensure that you read this section fully, and contact your local dealer should you be in

any doubt over correct operation procedures.

! Professional loudspeaker systems are capable of producing damage-inducing sound pressure levels, and hence care should be taken when setting your system up,

particularly when it comes to loudspeaker placement within a venue. Damage to the ear can result from levels above 90 dB under prolonged exposure.

Stand mounting

The XY-81 can be mounted from a loudspeaker stand using the integral polemount adapter for a standard 35 mm (1.4") loudspeaker stand. When mounting in this way, please

consider the following:

! Ensure your stand height is locked off and the tripod legs are positioned so as to be stable.

! Check the weight loading of your stands before attempting to mount the loudspeaker.

! Do not stack a second loudspeaker on top of the stand-mounted one.

! Ensure cables are run so as to leave enough slack to enable neat wiring, and thus reduce the risk of the speaker being pulled over. Loose cables should be covered or

taped down wherever possible to reduce trip hazards.

! When using poles on top of subwoofer systems, please observe similar precautions.

Ground stacking

! Ensure that the floor or stage surface can withstand the weight of the system.

! Wherever possible, avoid high stacks and use ratchet straps to secure loudspeakers together. Please also remember that vibrations from subwoofer systems can shake

other loudspeakers out of place, which may present a toppling hazard. The use of ratchet straps and non-slip material is recommended to prevent this.

Cabling and amplifier selection

The XY-81 is designed to be used with professional power amplifiers providing the following power outputs:

! 700 W/channel into 8 W

NOTE

A small power amplifier working too hard is more likely to damage a loudspeaker than a large power amplifier working within its operating range.

It is good practice to use an amplifier equal to the programme power rating of the loudspeaker — so as to retain sufficient headroom and good dynamic range. Care should be

taken during operation to avoid amplifier clipping — as this can cause serious damage to your loudspeakers. If in doubt, please contact your dealer who will be happy to assist

you in correct amplifier choice and setup.

Cabling

The XY-81 is supplied as standard with Neutrik SpeakON

nominal system impedance. Given below are the recommended maximum cable lengths for different cross-sections and impedances.

Conductor cross sectional area

1.0 mm

1.5 mm

2.0 mm

2.5 mm

4.0 mm

6.0 mm

! Pins 2+/2– on the Neutrik SpeakON

Protective DSP settings

WARNING

The XY-81 requires no DSP programme to function correctly. However, excessive low frequency information will cause the LF drive unit's excursion to increase, which can

result in damage to your loudspeaker.

The higher you raise the cut-off frequency on a high pass filter for an XY-81, the more headroom and overall sound pressure level output there is available. For most medium-to-

high level applications, we would recommend a minimum of a 70 Hz high pass filter with a 24 dB/octave slope to sufficiently protect the loudspeaker. For higher SPL applica-

tions, we would recommend raising this cut-off even higher. We would stress that the higher the cut-off frequency, the safer the loudspeaker will be.

Engb

™

NL4 connectors, wired pin 1+/1–. It is recommended that the resistance of your cable be less than one tenth of the

Maximum recommended cable length

4 W

11 m

17 m

22 m

29 m

44 m

66 m

™

connectors are wired together to allow link-through with 4-core cables.

8 W

16 W

22 m

44 m

34 m

68 m

44 m

88 m

58 m

116 m

88 m

176 m

132 m

264 m