Pioneer PDP 503CMX 사용 설명서 - 페이지 38

{카테고리_이름} Pioneer PDP 503CMX에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Pioneer PDP 503CMX 44 페이지. Pioneer 3rd, 4th % 5th generations plasma panel quick reference parts lists
Pioneer PDP 503CMX에 대해서도 마찬가지입니다: 기술 매뉴얼 (25 페이지), 빠른 참조 부품 목록 (12 페이지)

페이지 인쇄

1. Connection to Input1 and Input2

Additional Information

General problems

Problem

• No power

• Unit cannot be operated.

• Remote control does not

operate.

• INPUT is not changed.

• Picture is cut off.

• Strange color, light color, or

dark, or color misalignment

• Power is suddenly turned

off.

• No picture

Problems commonly mistaken as breakdown

Problem

• The screen is displayed in a

small size.

• Letter breakup on screen.

• A sharp sound is sometimes

heard from the cabinet.

• Bright portions of image

appear to be losing intensity.

• Speckles or noise appears on

screen.

• Stripes appear on the screen.

• Operation is not possible.

• Sound is heard from inside

the unit.

• Fan isn't moving.

• Fan speed changes.

• Is the power cord disconnected? (page 15)

• Has the MAIN POWER switch been switched on? (page 9)

• External influences such as lightning, static electricity, etc., may cause improper operation. In this

case, operate the unit after first turning the MAIN POWER on/off, or unplugging the power cord

and re-plugging it in after 1 to 2 minutes.

• Are batteries inserted with polarity (+, –) correctly aligned? (page 7)

• Are batteries worn out? (Replace with new batteries).

• Is a plug connected to the CONTROL IN connector?

When a plug is connected to the CONTROL IN connector, the signal from that connector is given

priority, thus disabling the remote control signal receiver (page 15).

• Is the Auto function being used? (page 29)

• Is the selected screen size correct?

Switch to another screen size (page 21).

• Are SCREEN mode adjustments such as picture size made correctly? (pages 26–27).

• Is the Point Zoom function being used? (page 23)

• Adjust the picture tone (page 25).

• Is the room too bright?

The picture may look dark in a room that is too bright.

• Is CLAMP POSITION setup correct? (page 18)

• The unit's internal temperature has increased. (Air vents are blocked.)

Remove any objects blocking vent or clean (page 31).

• Is the POWER MANAGEMENT or AUTO POWER OFF function set to ON? (page 24).

• Condensation has formed on internal parts due to suddenly increasing ambient temperature.

Allow condensation to dry thoroughly before using.

• Is connection to other components correct? (pages 12 to 14)

• Has setup been done correctly after connection? (pages 17 and 18)

• Is the correct input selected? (page 19)

• Is a non-compatible signal being input? (pages 12, 35 and 36)

• Is picture adjustment correct? (page 25)

• Check the input signal compatibility chart (pages 35 and 36).

• Is the correct screen size selected? (pages 21, 26 and 27)

• Adjust using "SCREEN" mode on the menu screen (page 27).

If there is still no improvement, this unit may be limiting the displayable range. Check the

personal computer input signal compatibility chart (pages 35 and 36).

• Expansion/contraction caused by surrounding temperature change may result in sound being

heard from the cabinet. This is not a malfunction.

• When the video input signal's level is too high, the bright portions may appear to be losing their

intensity.

Increase the adjustment level of the contrast and check the picture (page 25).

• May be caused by radio wave interference from appliances with motors such as hair dryers,

electric vacuum cleaners, electric power drills, ignition systems of cars, motorcycles etc., switch

devises such as thermostats etc., neon signs or electrical discharge from power lines etc.

• May be caused by radio wave mingling from TV station, FM station, amateur radios, public radios

(simplified radios) etc., or a nearby personal computer, TV, or video/audio component.

• A strong electromagnetic field may cause picture distortion and similar problems.

• External influences such as lightning strike, static electricity etc., may cause improper operation.

In this case, operate the unit after first turning the MAIN POWER ON/OFF, or unplugging the

power cord and re-plugging it in after 1 to 2 minutes.

• Normal sound of the cooling fan and internal sliding parts of the plasma display panel. Not a

malfunction.

• Fan is set to operate only after ambient temperature exceeds 35°C (differs depending on

installation conditions). Not a malfunction.

• Fan speed changes automatically in accordance with ambient conditions. Not a malfunction.

Possible Solution