Ariston LFF 8M122 사용 설명서 - 페이지 8

{카테고리_이름} Ariston LFF 8M122에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Ariston LFF 8M122 16 페이지. Ariston dishwasher operating instructions

페이지 인쇄

Refined salt and

rinse aid

Only use products which have been specifically designed

for dishwashers. Do not use table salt or industrial salt.

Follow the instructions given on the packaging.

If you are using a multi-function product, we recommend

that you add salt in any case, especially if the water is hard

or very hard. (Follow the instructions given on the packaging.)

If you do not add salt or rinse aid, the LOW SALT

LOW RINSE AID

indicator lights will remain lit.

Measuring out the refined salt

The use of salt prevents the formation of LIMESCALE on the

dishes and on the machine's functional components.

• It is important that the salt dispenser be never empty.

• It is important to set the water hardness.

The salt dispenser is located in the lower part of the dishwasher

(see Description)

and should be filled:

• When the LOW RINSE AID indicator light in the control panel

is lit

;

• When the green float

longer visible.

• See autonomy in the water hardness table.

1. Remove the lower rack and unscrew the

container cap (anticlockwise).

2. Only the first time you do this: fill the water

dispenser up to the edge.

3. Position the funnel

fill the salt container right up to its edge

(approximately 1 kg); it is not unusual for a little water to leak out.

4. Remove the funnel and wipe any salt residue away from the

opening; rinse the cap under running water and then screw it on.

It is advisable to perform this procedure every time you add

salt to the container.

Make sure the cap is screwed on tightly, so that no detergent

can get into the container during the wash cycle (this could

damage the water softener beyond repair).

Whenever you need to add salt, we recommend carrying

out the procedure before the washing cycle is started.

Setting the water hardness

For perfect water softener operation, it is essential that the

adjustment be based on the water hardness in your house. Ask

your local water supplier for this information. The factory setting

is for medium water hardness.

• Switch the dishwasher on using the On/Off button.

• Switch it off using the On/Off button

• Press and hold the START/PAUSE button

• Switch it on using the On/Off button

• Access the adjustment menu - the salt indicator light is lit.

• Select the desired level (1 to 5* max. based on the dishwasher

model) using the ECO button (see Table on water hardness).

• Switch it off using the On/Off button

• Setting is complete!

Only available in selected models.

on the cap of the salt dispenser is no

(see figure)

for 5 seconds.

Water Hardness Table

level

°dH

0 - 6

6 - 11

3 12 - 17

4 17 - 34

34 - 50

and

For values between 0°f and 10°f, we do not recommend the use of salt.

A setting of 5 may increase cycle duration.

(°dH = hardness measured in German degrees - °f = hardness

measured in French degrees – mmol/l = millimoles per litre)

Measuring out the rinse aid

Rinse aid makes dish DRYING easier. The rinse aid dispenser

should be filled:

• When the LOW RINSE AID indicator light on the panel/display

;

is lit

• When the dark optical indicator

becomes transparent.

and

1. Open the dispenser "D" by pressing and pulling up the tab

on the lid;

2. Carefully introduce the rinse aid as far as the maximum

reference notch in the filling space - avoid spilling it. If this

happens, clean the spill immediately with a dry cloth.

3. Press the lid down until you hear a click to close it.

NEVER pour the rinse aid directly into the tub.

Adjusting the amount of rinse aid

If you are not completely satisfied with the drying results, you

may want to adjust the quantity of rinse aid used.

• Switch the dishwasher on using the On/Off button.

• Switch it off using the On/Off button

• Press the START/PAUSE button

• Switch it on using the On/Off button

• Access the adjustment menu - the rinse-aid indicator light is lit .

• Select the level of rinse aid supply using the ECO cycle button.

• Switch it off using the On/Off button

• Setting is complete!

If the rinse aid level is set to ZERO, the rinse aid will not be

supplied and the low rinse aid indicator light will not be lit if you

run out of it.

A maximum of 4 levels can be set according to the dishwasher

model. The factory setting is for a medium level.

• If you see bluish streaks on the dishes, set a low number (1-2).

• If there are drops of water or limescale marks on the dishes,

set a high number (3-4).

Average autonomy

salt dispenser with 1

wash cycle per day

°fH

mmol/l

months

0 - 10

0 - 1

7 months

11 - 20

1.1 - 2

5 months

21 - 30

2.1 - 3

3 months

31 - 60

3.1 - 6

2 months

61 - 90

6.1 - 9

2/3 weeks

on the dispenser door "D"

three times