Aeotec ZWA019 매뉴얼

{카테고리_이름} Aeotec ZWA019에 대한 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Aeotec ZWA019 3 페이지. Water sensor
Aeotec ZWA019에 대해서도 마찬가지입니다: 사용자 설명서 (9 페이지), 사용자 설명서 (13 페이지), 사용자 설명서 (9 페이지)

페이지 인쇄

Water Sensor 7 Pro

ZWA019

Used in this guide.

Artículos utilizados en este manual / Utilisé dans ce guide / In dieser

Gebrauchsanweisung verwendete Bezeichnungen / Usato in questa guida /

Gebruikt in deze handleiding / Används i den här handboken.

Sensing head

Cabeza sensora / Tête de détection /

Sensorkopf / Testa sensibile / Hoofd

detecteren / Avkännande huvud

PIN:12345

Main base

Probe

Main front

Double-sided

uint

Tape for Main

enclosure

base unit (x2)

Note:

QR Code used for SmartStart inclusion.

DSK Code can be found on packaging. Do not

remove or damage them.

Remarque: code QR utilisés pour l'inclusion

SmartStart. Le code DSK peut être trouvé sur

l'emballage. Ne les enlevez pas et ne les

endommagez pas.

Hinweis: Der QR-Code wird für die

Screws (x4)

Double-sided

SmartStart-Einbindung verwendet. Der

Tape for

DSK-Code ist auf der Verpackung zu finden.

Sensor Head (x2)

Entfernen oder beschädigen Sie diesen nicht.

Important safety information.

Please read this and the online guide(s) at

support.aeotec.com/ws7p carefully. Failure to follow the

recommendations set forth by Aeotec Limited may be

dangerous or cause a violation of the law. The manufacturer,

importer, distributor, and / or reseller will not be held

responsible for any loss or damage resulting from not following

any instructions in this guide or in other materials.

To optimally detect water and leaks, Water Sensor 7 Pro is

intended for use in dry locations that then become wet.

Contains small parts; keep away from children.

Optimally placing Water Sensor 7.

The main unit of Water Sensor 7 Pro should be placed in a dry

location. It should be mounted vertically on a wall above the

place where you wish to monitor for potential floods or leaks. It

is the sensor probe of Water Sensor 7 Pro that detects liquids,

so the sensor probe must be placed in such a way that any

liquid or water of the leak will come into contact with it. When

placing Water Sensor 7 Pro probes do also consider in which

direction any flood or leak may flow and where one may occur.

Ensure that both of the probe contacts will be able to detect any

leak or flood. Only when the 2 probe contacts come into

contact with a liquid, Water Sensor 7 Pro will send a leak alert to

your Z-Wave gateway.

Quick start.

The following will step you through installing Water Sensor 7 Pro

and connecting it to your Z-Wave

network.

1. Press and hold the Latch on the larger sensor part and

separate the front from the back-mount plate and then pull

the case off completely.

2. Remove the Pull Tab to engage the sensor's pre-installed

batteries. The LED will flash red indicating that it is

powered on.

3. Add Water Sensor 7 Pro to your Z-Wave network;

a. If your Z-Wave gateway supports SmartStart: scan the

QR code on Water Sensor 7 Pro using the gateway's

app. Your sensor will join your Z-Wave network

automatically.

b. If your gateway does not support SmartStart;

i. Set your Z-Wave gateway into its 'add device' mode.

Refer to the gateway's manual if you are unsure of

how to perform this step.

ii. Press the sensor's Tamper Switch 3 times within 1.5

seconds; it is located on the lower right side with the

battery pointed forward.

iii. Now Water Sensor 7 Pro is joining your Z-Wave

network or its LED will blink green and red and then

joins your network.

iv. If pairing is successful, it will change to a green color

for 3 seconds before turning off.

If pairing failed, LED will flash red 3 times, it was

unable to join your Z-Wave network; repeat the step

or contact us for further support if needed.

4. After testing Water Sensor 7 Pro in your chosen installation

location, affix the main sensor's back-mount plate with

either the provided screws or double-sided tape.

Important. Make sure that the Water Sensor 7 Pro is

completely enclosed over the mounting plate, otherwise

the battery of your sensor will drain out within a few

days by remaining completely active.