Ariston OK 997E LDP X AUS S 사용 설명서 - 페이지 7

{카테고리_이름} Ariston OK 997E LDP X AUS S에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Ariston OK 997E LDP X AUS S 20 페이지.

페이지 인쇄

Electrical Connection

The electrical connection to the mains must be made on

the appliance. The power voltage and frequency are as

indicated on the rating plate.

! THIS APPLIANCE MUST BE EARTHED.

Fitting the power supply cable

3. Secure the cable by fastening the clamp screw.

4. Close the cover of the terminal board.

Connecting the power supply cable to the electricity

mains

Install a standardised plug corresponding to the load

indicated on the data plate (see opposite).

The appliance must be directly connected to the mains using

an omnipolar switch with a minimum contact opening of 3

mm installed between the appliance and the mains. The

switch must be suitable for the charge indicated and must

comply with current electrical regulations (the earthing wire

must not be interrupted by the switch). The supply cable

must be positioned so that it does not come into contact

with temperatures higher than 50°C at any point (the back

panel of the oven, for example).

! The installer must ensure that the correct electrical

connection has been performed and that it is fully compliant

with safety regulations.

Before connecting the appliance to the power supply, make

sure that:

• The appliance is earthed and the plug is compliant with

the law;

• The socket can withstand the maximum power of the

appliance, which is indicated on the data plate (see

below);

1. Open the terminal board

by inserting a screwdriver

into the side tabs of the

cover. Use the screwdriver

as a lever by pushing it

down to open the cover (see

diagram)

2. Install the power supply

cable by loosening the

cable clamp screw and the

three wire contact screws

L-N-

Connect the wires to the

corresponding terminals:

the Blue wire to the terminal

marked (N), the Brown wire

to the terminal marked (L)

and the Yellow/Green wire

to the terminal marked

(see diagram).

• The voltage is in the range between the values indicated

on the data plate (see below);

• The socket is compatible with the plug of the appliance.

If the socket is incompatible with the plug, ask an

authorised technician to replace it. Do not use extension

cords or multiple sockets.

!Once the appliance has been installed, the power supply

cable and the electrical socket must be easily accessible.

! The cable must not be bent or compressed.

! The cable must be checked regularly and replaced by

authorised technicians only (see Assistance).

! The manufacturer declines any liability should

these safety measures not be observed.

APPLIANCE SPECIFICATIONS

width 43.5 cm

Dimensions*

height 41 cm

depth 41 cm

Volume*

74 l

width 45.6 cm

Dimensions**

height 41 cm

depth 41 cm

Volume**

77 l

voltage: 220 - 240 V ~50 Hz

Electrical

maximum power absorbed

connections

3400 W (see data plate)

Directive 2002/40/EC on the

label of electric ovens.

Standard EN 50304

ENERGY LABEL

Declared energy consumption

for Forced convection

Class – heating mode:

ECO

This appliance conforms to the

following European Economic

Community directives:

2006/95/EEC dated 12/12/06

(Low Voltage) and subsequent

amendments – 2004/108/EEC

dated 15/12/04

(Electromagnetic

Compatibility) and subsequent

amendments - 93/68/EEC

dated 22/07/93 and

subsequent amendments.

2012/19/EEC and subsequent

amendments.

1275/2008 Stand-by/off mode

* Only for models with drawn rails.

** Only for models with wire rails.

AUS