Whirlpool 2DLSQ8000JQ5 설치 지침 - 페이지 4

{카테고리_이름} Whirlpool 2DLSQ8000JQ5에 대한 설치 지침을 온라인으로 검색하거나 PDF를 다운로드하세요. Whirlpool 2DLSQ8000JQ5 5 페이지. 120-volt 60-hz washer
Whirlpool 2DLSQ8000JQ5에 대해서도 마찬가지입니다: 사용 및 관리 매뉴얼 (12 페이지)

페이지 인쇄

Drain

hose

ln|et hose

(to water

faucets)

1/4"

® To prevent the drain hose

from coming off or leaking,

it must be installed per the

following

instructions.

Wet the inside end of the drain

hose with tap water DO NOT USE

ANY OTHER LUBRmCANT.

Squeeze ears of drain hose clamp

with pliers to open and place

clamp over the end of the drain

hose.

Open clamp and push end of drain

hose onto drain connector until

hose contacts ribbed stop.

Place clamp over area marked

"clamp".

Release clamp.

e Standpipe

laundry

tub dra|n

system:

Open yellow damp and slide over

"hook"

end of drain hose

to secure the rubber

and corrugated

sections together.

F|oor drain

system:

Do Not instal[ "hook"

LD "_

end of drain hose to

corrugated

section. Consult your

plumber for proper installation.

Run wate_

through

i_'_'.' . _ R_,._

both faucets into

a bucket to get

rid of particles in the water lines

that might clog hoses. Mark the hot

water faucet.

Put "hook"

end of drain

® hose into laundry tub or

standpipe. Check for proper length

of drain hose.

To prevent

drain

water

from

going

bach

into

washer:

Do Not

straighten

"hooh"

end

of drain

hose and

force

excess

drain

hose

into

standpipe.

Not

lay e×¢ess

drain

hose

in bottom

of laundry

tub.

Check inlet hoses

periodically.

Replace inlet

hoses if you find bulges,

kinks, cuts, wear or leaking.

Replace inlet hoses after

five years of use.

blots

are pBastk°

Do Not

strip

crossthread.

cold

water

inlet

valve

hot water

inlet valve

Attach bottom

hose from

® the inlet marked "H" to

the hot water faucet. Attach top

hose from the inlet marked "C" to

the cold water faucet. Tighten

couplings to faucets DO NOT

OVERTIGNTEN;

this could cause

damage to couplings.

® Stack two corner

posts

on top of each other

and postion

them

3 inches from

each side of

the washer.

Grasp the top, front

corners

of the washer

and tilt

backward

until

bottom,

front

washer

is 3-4 inches off the floor

and slide corner

posts under

washer

as shown.

1/2"

® Screw nut down on legs

to within 1/2 inch of base.

Insert

legs into correct

holes at each front

corner

of washer

until

nuts touch

washer.

DO NOT

tighten

nuts until Step 16.

i Grasp top front

corners

tilt washer

backward

and remove

corner

post(s).

Gently

lower washer

to floor.

Use outside

corners

of the

cabinet

move

washer

to its

final

location.

Remove

cardboard

or hardboard

from

under

washer.

Tilt washer forward

® slightly so that back legs

are about 1 inch off floor. Drop

washer to floor. Check levelness of

the washer by placing a carpenter's

level on top of the washer, first side

to side; then front to back.

If washer is not level, repeat Step

11, and adiust the front legs up or

down. Then repeat Steps 14 E<15.

When

washer

is level, use

wrench

to turn

nuts on front

legs up tightIy

against

washer

base. |f nuts are not tkJht

against

washer

base, the

washer

may vibrate.

dra|n

hose:

NOTE:

Use shipping

strap to

secure drain

hose. Water pressure

could

cause drain

hose to come

out of standpipe

or laundry

tub if

drain

hose is not secured.

After shipping strap has been

removed (Step 1), look for the

words "cut here" marked on the

shipping strap, about 16 inches

from plug end

Cut the shipping strap at this

mark. Pull shipping strap out of

the power supply cord.

Check

that

hose

is not

twisted

or kinked

and

is securely

place.

Put "hook" end of drain hose in

laundry tub or standpipe. Tightly

wrap the shipping strap around the

drain hose and laundry tub or

standpipe as shown in Figures AoB.

Push plug into the nearest hole in

the shipping strap.

If the water inlet

faucets and drain

standpipe are

recessed, put

"hook"

end of

drain hose in

standpipe. Tightly

wrap the shipping

strap around the

drain hose and

strap

faucet body (not the handles or

stems) as shown in Figure C. Push

plug into the nearest hole in the

shipping strap.

i;'

:cs

If a Ion( er drain hose is needed, use

a 21" or 54" drain hose and

Connector Kit, Part No. 285442. If

drain hose must be shortened, use

Connector Kit Part No. 285442.

These parts are available from your

local dealer or authorized

parts

distributor.

Note:

|f washer

is moved

adjust

drain

hose,

the

washer

must

be IeveIe¢ tl again.

Repeat

Steps

1S°16.

Place

cardboard

under

the

washer

and

carefully

move

washer

to avoid

damacJin

9 floor

¢overin

Panel C