Whirlpool 3RLSQ8533 사용 및 관리 매뉴얼 - 페이지 7

{카테고리_이름} Whirlpool 3RLSQ8533에 대한 사용 및 관리 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Whirlpool 3RLSQ8533 12 페이지. Two speed automatic washer
Whirlpool 3RLSQ8533에 대해서도 마찬가지입니다: 사용 및 관리 매뉴얼 (11 페이지), 설치 지침 (5 페이지)

페이지 인쇄

6. Set the TEMPERATURE selector to the correct setting for the

type of fabric and soils being washed. Use the warmest water

safe for fabric. Follow garment label instructions.

Your washer uses automatic temperature control (on some

models) to maintain a uniform water temperature by

regulating the incoming hot and cold water. This helps

eliminate undissolved detergent and ensures consistent

cleaning results. The Hot and Warm settings on this washer

will be cooler than you are accustomed to. Wash

temperatures in this washer are lower than the temperatures

you may be used to in conventional washers.

NOTE: Make sure that both the hot and cold water taps are

fully turned on, or the automatic temperature control feature

will not work properly.

Water Temp

Use For

Hot

Whites and pastels

Heavy soils

Warm

Bright colors

Moderate to light soils

Cold

Colors that bleed or fade

Light soils

NOTE: In wash water temperatures colder than 60ºF

(15.6ºC), detergents do not dissolve well. Soils can be difficult

to remove. Some fabrics can retain wear wrinkles and have

increased pilling (the formation of small lint-like balls on the

surface of garments).

7. (OPTIONAL) Some models have an EXTRA RINSE selector.

For an additional rinse and spin at the end of a wash cycle,

set the EXTRA RINSE selector to ON. On some models, the

Extra Rinse feature is part of the cycle.

8. (OPTIONAL) Some models have an END OF CYCLE SIGNAL

selector. Set the END OF CYCLE SIGNAL selector to ON if

you want your washer to alert you when the wash cycle is

complete. The signal is helpful when you are washing items

that should be removed from the washer as soon as the cycle

ends.

9. Push in the Cycle Control knob and turn it clockwise to the

wash cycle you want. Reduce the wash time when using a

small load size setting. See "Selecting a Cycle and Time."

Pull out the Cycle Control knob to start the washer.

To stop or restart your washer

To stop the washer at any time, push in the Cycle Control

knob.

To restart the washer, close the lid (if open) and pull out

the Cycle Control knob.

Adding bleach to models without a bleach dispenser

If desired, add measured liquid chlorine bleach after the washer

starts agitating. Pour diluted bleach around the agitator, not

directly onto the load. Undiluted bleach will damage any fabric it

touches. (See "Adding Liquid Chlorine Bleach.")

Adding softener to models without a fabric softener

dispenser

If desired, add measured liquid fabric softener to the final rinse

water. Always dilute fabric softener with ¹⁄₂ to 1 cup (125 to

250 mL) cup of warm water. Undiluted fabric softener can stain

fabrics. (See "Adding Liquid Fabric Softener.")

Selecting a Cycle and Time

This section describes the available wash cycles and will help

you make the best cycle selections for your wash loads. Each

cycle is designed for different types of fabric and soil levels.

The washer pauses briefly throughout each cycle. These

pauses are normal. Refer to "Normal Sounds" to learn more

about the sounds you may hear during a wash cycle.

Refer to "Understanding Washer Cycles" to learn what

happens during a wash cycle.

NOTE: This manual covers several different washer models. The

washer you have purchased will not have all of the cycles

described.

Regular/Heavy cycle

This cycle features high-speed agitation followed by brief periods

of low-speed agitation for cleaning sturdy fabrics and heavily

soiled loads that need maximum soil removal. Select Super Wash

or Regular depending on whether your load is moderately or

heavily soiled. For improved cleaning, use twice the amount of

detergent recommended for a wash cycle. The Heavy cycle

features Extra Rinse as part of the cycle.