Whirlpool 3XLBR5432JQ4 사용 및 관리 매뉴얼 - 페이지 10
{카테고리_이름} Whirlpool 3XLBR5432JQ4에 대한 사용 및 관리 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Whirlpool 3XLBR5432JQ4 12 페이지. 120-volt 60-hz washer
Whirlpool 3XLBR5432JQ4에 대해서도 마찬가지입니다: 설치 지침 (5 페이지)
페이지 인쇄
Washer
makes noise
•
Is the load balanced
and the washer
level?
The wash
load should
be balanced
and not overloaded.
The washer must be level. The front feet should be properly
installed and the nuts tightened.
Reset the rear leveling legs
(if needed). See the Installation Instructions.
Did you completely
remove the yellow shipping strap with
cotter pins?
See the Installation Instructions.
Are the gears
engaging
after
the drain
and before
spin, or
is the upper
part
of agitator
clicking
during
wash?
These
are normal
washer
noises.
Washer leaks
•
Check the following:
Are the fill hoses tight? Are the fill hose washers properly
seated? Is the drain hose clamp properly installed? See the
Installation Instructions.
Is the sink or drain clogged?
Sink and standpipe must be able to handle 17 gallons (64 L)
of water per minute.
Is water deflecting off the tub ring or the load?
Center the tub before starting the washer.
The wash load should be balanced and not overloaded. The
fill or spray rinses can deflect off the load.
The washer must be level. The front feet should be properly
installed and the nuts tightened.
Reset the rear leveling legs
(if needed). See the Installation Instructions.
•
Check
household
plumbing
for leaks.
Washer
basket is crooked
•
Was the washer
basket
pulled
forward
during
loading?
The wash
load should
be balanced
and not overloaded.
Push
the basket
to the center
before starting
wash.
•
Is the load balanced
and the washer
level?
The wash
load should
be balanced
and not overloaded.
The washer must be level. The front feet should be properly
installed and the nuts tightened.
Reset the rear leveling legs
(if needed). See the Installation Instructions.
•
The washer basket moves while washing.
This is normal.
Agitator operation
•
The top of the agitator is loose, or moves in only one
direction.
This is normal.
Dispensers clogged or bleach leaking
•
Did you follow the manufacturer's
directions
when adding
detergent
and fabric softener
to the dispensers?
Measure detergent and fabric softener. Carefully pour into the
dispensers. Wipe up all spills.
Dilute fabric softener in the fabric softener dispenser.
•
Did you put powdered
or color-safe
bleach in the liquid
chlorine
bleach dispenser?
Add powdered or liquid color-safe bleach directly to the
basket. Do not use the chlorine bleach dispenser for color-
safe bleach.
Load too wet
•
Did you use the right cycle for the load being washed?
Select a cycle with a higher spin speed (if available).
•
Did you use a cold rinse?
Cold rinses leave loads wetter than warm rinses. This is
normal.
Residue or lint on load
•
Did you sort properly?
Sort lint givers (towels, chenille) from lint takers (corduroy,
synthetics). Also sort by color.
•
Did you overload the washer?
The wash load must be balanced and not overloaded. Lint
can be trapped in the load if overloaded. Wash smaller loads.
•
Checkthe
following:
Was paper or tissue left in the pockets?
Did you use enough detergent? Follow manufacturer's
directions.
Use enough detergent to hold the lint in the water.
Is your water colder than 70°F (21 °C)? Wash water colder
than 70°F (21°C) may not completely
dissolve the detergent.
Stains on load
•
Did you follow the manufacturer's
directions
when adding
detergent
and fabric
softener?
Measure detergent and fabric softener. Use enough detergent
to remove soil and hold it in suspension.
Dilute fabric softener and add to the rinse portion of a cycle
only. Do not drip fabric softener on clothes.
•
Is there above average iron (rust) in water?
You may need to install an iron filter.
•
Did you properly
sort the load?
Sort dark clothes from whites and lights.
•
Did you unload the washer
promptly?
To avoid dye transfer, unload the washer as soon as it stops.
Load is wrinkled
•
Did you unload the washer promptly?
Unload the washer as soon as it stops.
•
Did you use the right cycle for the load being washed?
Use the Permanent Press cycle or another cycle with low spin
speeds (if available) to reduce wrinkling.
•
Did you overload the washer?
The wash load must be balanced and not overloaded. Loads
should move freely during washing.
•
Was the wash water
warm enough to relax wrinkles,
or
are you using warm
rinses?
If safe for the load, use warm or hot wash water. Use cold
rinse water.
•
Are the hot and cold water hoses reversed?
Check to be sure the hot and cold water hoses are connected
to the right faucets. See the Installation Instructions.
10