Whirlpool 7MWFW87HEDC0 사용 및 관리 매뉴얼 - 페이지 19

{카테고리_이름} Whirlpool 7MWFW87HEDC0에 대한 사용 및 관리 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Whirlpool 7MWFW87HEDC0 48 페이지.

페이지 인쇄

Troubleshooting

First try the solutions suggested here or visit our website at www.whirlpool.com/product_help

In Canada www.whirlpool.ca

for assistance and to possibly avoid a service call.

Washer won't run or fill,

washer stops working

(cont.)

Washer not draining/

spinning, loads are

still wet

Door locked at end

of wash cycle

Door will not unlock

Incorrect or wrong

wash or rinse

temperatures

Not using HE detergent or using too

much HE detergent.

Door not opened between cycles.

Drain hose extends into standpipe

farther than 4.5" (114 mm).

Only use HE detergent. Suds from regular detergents can

slow or stop the washer. Always measure detergent, following

manufacturer's

directions based on your load requirements.

To remove suds, cancel cycle. Select DRAIN & SPIN with Extra

Rinse. Touch and hold START. Do not add more detergent.

The drain hose is clogged, or the

end of the drain hose more than

96" (2.4 m) above the floor.

The drain hose fits too tightly

The drain hose should be loose yet fit securely. Do not seal the

in the standpipe, or is it taped

drain hose with tape. The hose needs an air gap. See "Secure

to the standpipe,

the Drain Hose" in Installation Instructions.

Using cycles with a slower spin

Cycles with slower spin speeds remove less water than cycles

speed,

with fast spin speeds. Use the recommended

cycle/speed

spin

for your garment.

Washer not loaded as recommended.

The load may be out of balance.

Not using HE detergent or using too

much HE detergent.

Small items may have been caught

in the pump or stuck between the

washer drum and the outer tub.

There are too many clothes in the

Wash & Dry cycle.

Water remaining in washer after cycle.

Fan Freshen/Turn bleFresh '_option

is on.

Door locks when cycle has started.

Check for proper water supply.

After 3 wash cycles in a row are completed, the door must be

opened and then closed before a new cycle can begin.

Check drain hose for proper installation. Use drain hose form

and securely attach to drainpipe or tub. Do not tape over drain

opening.

Lower drain hose if the end is higher than 96" (2.4 m) above

the floor. Remove any clogs from drain hose. See 'qnstallation

Requirements"

in Installation Instructions.

A tightly packed or unbalanced

load may not allow the washer

to spin correctly, leaving the load wetter than normal. See

"Cycle Guide" for load size recommendation

for each cycle.

Avoid washing single items. Balance a single item such as a rug

or jeans jacket with a few extra items.

Use only HE detergent. Suds from regular detergent or using too

much detergent can slow or stop draining or spinning. Always

measure and follow manufacturer's

directions for your load.

To remove extra suds, select DRAIN & SPIN with Extra Rinse.

Do not add detergent.

Check the drum for any items sticking through the drum holes.

Empty pockets and use garment bags when washing small

items.

Only use the Wash & Dry cycle for 2=4 lightly soiled synthetic

garments, athletic uniforms, or workout wear.

Select DRAIN & SPIN to remove any water remaining in the

washer. The washer door will unlock at the end of the drain.

While this option is on, the fan blows (FanFresh _'> option only)

and the load is tumbled periodically for up to 12 hours

(FanFresh _ option) or 6 hours (TumbleFresh _option). The door

remains locked during this time. To unlock the door, cancel

the option by touching POWER.

If the "Add Garment" light is lit, touch START once. The door

will unlock.

Make sure hot and cold inlet hoses are not reversed.

Washing many loads.

Both hoses must be attached to both washer and faucet, and

have both hot and cold water flowing to inlet valve.

Check that inlet valve screens are not clogged.

Remove any kinks in hoses.

Your hot water tank may not have enough hot water to keep up

with the number of hot or warm washes. This is normal.