Whirlpool AWA 1000 빠른 시작 매뉴얼 - 페이지 2

{카테고리_이름} Whirlpool AWA 1000에 대한 빠른 시작 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Whirlpool AWA 1000 2 페이지.

페이지 인쇄

ENERGY AND WATER CONSUMPTION DATA

Programme

Temperature

(°C)

Cotton + Intens. Rinse

Cotton

Coloured

Quick Wash + Half Load

Synthetics + Half Load

Delicate

Wool

Prewash cycle increases programme duration approximately 15 min. Consumption values were measured in normalized

conditions in compliance with standard IEC 60 456. Consumption data in the home may vary with respect to the values in

the table in relation to the water supply pressure and temperature, the load and the type of wash. The data on the "Energy

Label" refer to the programme "Cotton 60°C".

* The remaining time indicator can similarly deviate from the values in the table, because it takes into account the

household conditions applicable at that time.

**To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains

the water out.

PREPARATION OF WASH CYCLE

1. Close the drum flaps and check that they are

properly locked.

2. Add detergents and additives into the dispenser

to no more than the "MAX" level mark, as

follows:

•

Programme with pre and main wash

•

Main wash programme without prewash

•

Fabric softeners and conditioners

•

Chlorine bleach

•

Stain remover agents

•

Anti-scale agents (if necessary)

3. Turn the programme selector knob clockwise to

the desired programme.

4. Turn the temperature knob to the required

temperature.

5. Turn the spin speed knob to the required spin

speed.

Load

Water

Energy

Programme time

(kg)

(l)

(kWh)

(min)

5.0

1.80

115

5.0

1.15

115

2.0

0.80

100

2.0

0.40

100

2.5

0.50

2.0

0.40

1.5

0.65

1.0

0.55

PRESS ANY DESIRED OPTION BUTTON(S)

Intensive Rinse button "Rinçage Intensif"

• The water level increases for improved rinsing

efficiency.

• This option is particularly suitable for areas with

very soft water when washing baby linen and

helps people with skin allergies.

• For improved garment care it is advised to use

the option for the Cotton 90° C and the Coloured

60° C programme.

"Half Load" button "Charge Reduite"

• Reduces the water consumption in the "Cotton"

and "Synthetics" programmes especially during

the rinse.

• Especially suitable for lightly soiled or small loads

(reduces the quantity of detergent).

• Not suitable for high temperature programmes.

Rinse Hold button "Arrêt Cuve Pleine"

• The laundry remains in the last rinse water,

without progressing to the spin cycle to avoid

creasing and prevent colours from changing.

• This option is especially recommended for the

"Synthetics" or "Delicate" programmes.

• This option is perfectly suitable if you wish to

postpone the spin or you don't wish to spin the

clothes.

Note: the programme selector stops on "

Terminate the "Rinse Hold" option.

• Press the "Rinse Hold" button again; the

programme will terminate automatically with

the spin cycle corresponding to the previously

selected wash programme.

• If you do not wish to spin the clothes, switch

off the appliance by pressing the "On/Off"

button. The pilot light goes out. Turn the

programme selector to the "Drain" position and

switch on the appliance.

PROGRAMME START

Open the water inlet tap and press the "On/Off"

button. The pilot lamp lights up.

DOOR LOCK

During the running programme, the door cannot be

opened.

The door locks automatically in all programmes.

If the programme is stopped or if an electrical

power failure occurs, the door unlocks

automatically after about 1 minute.

PROGRAMME END

•

The programme selector knob is at "STOP", the

pilot lamp lights.

1. Press the "On/Off" button. The pilot light

goes out.

2. Cancel the options by pressing the appropriate

buttons.

3. Turn the water supply tap off.

4. Wait for the door to unlock (about 1 minute).

5. Open the door and the drum flaps and unload

the machine.

SELECTING A NEW PROGRAMME, SPIN SPEED,

OPTIONS AFTER PROGRAMME START

1. Press the "On/Off" button to switch off the

appliance.

The pilot light goes out.

2. Select the new programme, temperature, spin

speed and options.

3. Press the "On/Off" button to switch on the

appliance.

The pilot light lights.

TO STOP, RESET A PROGRAMME BEFORE THE END

1. Press the "On/Off" button to switch off the

appliance.

The pilot light goes out.

2. Set the programme selector on "Drain".

3. Press the "On/Off" button to start the "Drain"

programme.

Only open the door when the programme

selector is at "STOP" and the door is unlocked

(after approximately 1 minute).

NOTES AND INDICATIONS FOR USE

• After switching your washing machine on, it

does not start immediately: it needs some

seconds in order to lock the door, fill water and

then drum starts turning.

• Spinning has an interrupted start-up: the drum

starts and stops running several times, to

improve spin efficiency and to better balance

the laundry.

• At the end of the spinning cycle the drum goes

on reversing for some minutes: this helps you

unloading the laundry.

• Do not exceed in detergents dosage: excessive

foam formation may prevent spinning.

• Your imbalance detection and correction

system reduces spin speed or interrupts the

spin automatically in case of imbalance load -

see "troubleshooting guide".

• Your machine has a new, electronically-

controlled motor: don't be surprised by its

sound.

• If you want to change the programme during

the wash cycle, remember to switch the

machine off before turning the programme

selector knob.

Whirlpool is a registered trademark of Whirlpool USA.

5019 312 10068/A