Whirlpool AWO/D 42420 사용자 설명서 - 페이지 4
{카테고리_이름} Whirlpool AWO/D 42420에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Whirlpool AWO/D 42420 32 페이지.
페이지 인쇄30105993GB.fm Page 2 Wednesday, December 27, 2006 6:23 PM
CONSUMPTION DATA
Temperature
Programme
(°C)
95
Cotton / Antibacterial
Cotton
60
Cotton with "Eco"***
60
Cotton
40
Synthetics
60
Synthetics
40
Delicates
30
Daily load 60min
40
Quick wash 30min
30
Wool
40
Handwash
40
Consumption values were measured in normalized conditions in compliance with Standard IEC/EN 60 456. Consumption data in the home
may vary with respect to the values in the table in relation to the water supply pressure and temperature, the load and the type of wash.
*
The remaining time indicator can deviate from the values in the table, because it takes into account the household conditions
applicable at that time.
**
To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.
***
Reference Programme for Energy Label.
ADD DETERGENTS, CLOSE THE DOOR
AND SELECT THE PROGRAMME
Add detergent as indicated on the front page and as
described in the chapter "Detergent and Additives"
in your Instructions for Use.
Close the door and turn the programme selector to
the desired programme and temperature. The
indication lamp next to the "Start/Pause" button
flashes.
SELECT ANY DESIRED OPTION
Push the button(s) of any option(s) desired - the
respective indication lights up.
When the combination of programme and additional
option(s) is not possible, the indication lights switch off
automatically. Unsuitable combinations of options are
deselected automatically.
"Prewash" button
• Only for heavily soiled loads (for example sand,
granular dirt) sensible. Increases the cycle time
by approximately 15 min.
"Eco" button
• With a modified temperature profile and a slightly
prolonged washing duration, the optimum
combination of excellent washing result and even
lower energy consumption is achieved.
Black process 45.0° 100.0 LPI
Load
Water
Energy
Approx. Programme
Duration
(kg)
(l)
(kWh)
(hours : minutes)*
6.0
59**
1.90
2:00
6.0
49
1.14
2:10
6.0
49
1.02
2:20
5.0
56
0.70
2:00
2.5
50**
0.80
1:35
2.5
46
0.50
1:20
1.5
60
0.50
0:45
3.0
41
0.50
1:00
3.0
41
0.40
0:30
1.0
60
0.50
0:45
1.0
45
0.50
0:40
"Cold wash" button
• Water is heated only up to 20°C.
• Suitable for delicate laundry items with wash
temperature recommendation of max. 30° on
the care label.
• Selectable only on the lowest temperature step
of each programme.
"Rinse hold" button
• The laundry remains in the last rinse water
without progressing to the final spin cycle to avoid
creasing and prevent colours from changing.
• This option is particularly recommended for the
programmes "Synthetics", "Daily load" and
"Delicates".
• This function is particularly useful if you want to
postpone spinning to a later time, or if you want
to drain only.
Note: The programme stops to "Rinse hold" at
the time the "Anticrease" light in the programme
sequence indicator is on. The indication lamp
next to the "Start/Pause" button flashes.
• If you select "Rinse Hold", do not leave the
laundry items to soak for too long.
Terminate the "Rinse hold" option:
• Press the "Start/Pause" button; the
programme will terminate automatically with the
final spin cycle for the present wash programme.
• If you do not wish to spin the clothes, turn the
programme selector knob to the "Drain"
programme and press the "Start/Pause" button.
"Variable spin" button
• Every programme has a predefined spin speed.
• Press the button to set another spin speed.
• If spin speed "0" is selected, the final spinning is
cancelled but intermediate spin peaks remain
during rinse. The water is drained out only.
START DELAY
The "Start Delay" allows to run the machine at the
consumer's convenience, for example at night when
electricity is cheaper.
• Select programme, temperature and options.
• Press the "Start Delay" button to select the
delay time by 1, 3, 6, 9 or 12 hours.
• Press the "Start/Pause" button.
The indication next to the "Start Delay" button
lights up and goes off when the programme starts.
• Once having pressed the "Start/Pause" button,
the countdown of the time delay begins. When
the programme starts, the start delay indicator
light goes off and is replaced by the programme
sequence indication.
• After the "Start/Pause" button has been pressed,
the number of hours preselected can be reduced
by pressing again the "Start Delay" button.
To cancel the "Start Delay"
..before you press the "Start/Pause" button:
• Turn the programme selector to another
position or press the "Reset" button.
..after having pressed the "Start/Pause" button:
• Press the "Reset" button for at least 3 seconds -
the start delay indicator light goes out.
PROGRAMME START
Open the tap and press the "Start/Pause" button.
The indication lamp next to the "Start/Pause" button
lights up. The programme sequence indicator shows
the current programme phase, running from left to
right through Wash, Rinse, Spin/Drain.
When the programme phase is finished, the
corresponding indication goes out.
"DOOR OPEN" INDICATION
Before starting and after end of a programme, the
lamp lights to show that the door can be opened. As
long as a wash programme is running, the door
remains locked and must on no account be forced
open. In case you have an urgent need to open it
during a running programme, refer to "Cancel
(Reset) a running programme before the end".
RED INDICATIONS
"Service"
Lighting up of the "Service" indication can be caused by
a fault in an electrical component. Refer to the
"Troubleshooting Guide" in your Instructions for Use;
if the fault persists, contact our After Sales Service.
"Water tap closed"
The appliance has no or insufficient water supply.
Open the water tap; if the indication still lights up,
refer to the "Troubleshooting Guide" in the
Instructions for Use.
"Clean pump"
Waste water is not pumped out. Check whether the
drain hose is kinked or the filter must be cleaned; in
the latter case refer to the Instructions for Use
("Removing the Filter").
PROGRAMME END
• All the lights of the programme sequence indicator
are off, and the "Door open" indication lights up.
1. Turn the programme selector to the "Off/O"
position.
2. Close the water tap.
3. Open the door and unload the machine.
4. Leave the door ajar to allow the drum to dry.
CHANGE PROGRAMME AND/OR OPTIONS
AFTER PROGRAMME START
1. Press the "Start/Pause" button to pause the
programme. The light flashes.
2. Select the new programme (with temperature),
any options and another spin speed if you want.
3. Press the "Start/Pause" button again. The new
programme continues at the same position
where the previous programme was interrupted.
Do not add detergent for this programme.
CANCEL (RESET) A RUNNING
PROGRAMME BEFORE THE END
The "Reset" button cancels a programme before
the end.
• Press the "Reset" button for at least 3
seconds. Any existing water is drained out
before the door can be opened.
Whirlpool is a registered trademark of Whirlpool USA
5019 301 05993