Whirlpool Cabrio WTW6200VW0 사용 및 관리 매뉴얼 - 페이지 18

{카테고리_이름} Whirlpool Cabrio WTW6200VW0에 대한 사용 및 관리 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Whirlpool Cabrio WTW6200VW0 48 페이지. Automatic washer

페이지 인쇄

To use washer

again:

1. Flush water pipes and hoses. Reconnect water inlet hoses.

Turn on both water faucets.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension

cord.

Failure to follow these instructions can result in death,

fire, or electrical

shock.

Plug in washer or reconnect power.

Run the washer using any cycle and a Super Load Size water

level to clean the washer and remove the antifreeze, if used.

Use 1/2the manufacturer's

recommended

amount for a

medium-size

load.

To transport

the washer:

1. Shut off both water faucets.

2. Disconnect

and drain water inlet hoses.

3. If the washer will be moved during freezing weather, put 1 qt

(1 L) of R.V.-type antifreeze in the basket. Run washer on the

Rinse & Spin setting for about 30 seconds to mix the

antifreeze and remaining water.

4. Disconnect

the drain from the drain system.

5. Unplug the power cord.

6. Place the inlet hoses into the basket.

7. Drape the power cord and drain hose over edge into the

basket.

8. Place foam packing ring from the original shipping materials

in the top of washer. If you do not have the original foam

packing ring, place heavy blankets, towels, etc. into basket

opening. Close the lid and put a piece of tape over the lid and

down to the front of the washer. Keep lid taped until the

washer is placed into the new location.

Reinstalling

the washer

1. Follow the "Installation

Instructions"

to locate, level and

connect the washer.

2. Run the washer using any cycle and a Super Load Size water

level to clean the washer and remove the antifreeze, if used.

Use 1/2the manufacturer's

recommended

amount for a

medium-size

load.

TROUBLESHOOTING

First try the solutions suggested here and possibly avoid the cost of a service call...

Washer displaying code messages

J E "LF"

•

(Washer is taking too long to fill)

Check the following:

Are the water inlet hoses kinked or clogged?

Are the water inlet valve screens clear?

Press PAUSE/CANCEL to clear display.

•

"Ld" (Washer is taking too long to drain water from

the wash tub)

Check the following:

Is the drain hose kinked or clogged?

Is the drain hose installed properly? See "Connect Drain

Hose." Press PAUSE/CANCEL to clear display.

•

UL "uL" (Unbalanced

Load)

If the load is unbalanced,

the washer will display this code

while running an imbalanced load correction routine at the

end of the wash cycle and before the final spin. If the code

remains and the wash cycle dial is flashing after the recovery

routine has stopped, open lid and redistribute the load. Close

lid and press START.

•

oL "oL" (Over Load)

Is the washer overloaded? The washer has attempted

to fill

and begin the wash cycle. If the washer is overloaded, it will

drain any water and detergent that was added during the fill.

To correct the overload, remove several items and add

detergent. Close lid and press START.

_d "Sd" (Suds Detected)

Did you add too much detergent?

Always measure detergent. Follow detergent manufacturer's

directions.

If excessive suds are detected, the washer will display this

code while running a suds reduction correction routine at the

end of the wash cycle. The suds reduction routine removes

extra suds and assures proper rinsing of your garments. If the

code remains and the wash cycle dial is flashing after the

recovery routine has stopped, re-select your desired cycle

using cold water. Press START. Do not add detergent.

•

_ _d "lid" (Lid Opened)

Is the lid open? Close the lid to clear the display.

•

HE "HC" (Cold and Hot hoses switched)

This code will appear at the end of the wash cycle to indicate

that the cold and hot water inlet hoses are switched.

If an

error code does not appear but you are experiencing

poor

washing performance,

check to see whether the inlet hoses

are reversed. See "Connect the Inlet Hoses."

•

dL "dL" (Door/Lid cannot lock)

Indicates lid is not locked. Check for items caught in the lid

keeping it from closing. Press PAUSE/CANCEL once to clear

the code.

•

dLJ "dU" (Door/Lid cannot unlock)

Is there excessive weight on the lid, such as a basket of

laundry? Excessive weight will keep the lid from unlocking.

Press PAUSE/CANCEL once to clear the code.