Whirlpool 2188766 사용 및 관리 매뉴얼 - 페이지 8
{카테고리_이름} Whirlpool 2188766에 대한 사용 및 관리 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Whirlpool 2188766 24 페이지. Side by side refrigerator
페이지 인쇄4. Align and replace the top left hinge as shown (see Graphic 4).
Tighten screws.
WARNING
Electrical Shock Hazard
Reconnect both ground wires.
Failure to do so can result in death or
electrical shock.
Style 1
Reconnect both ground wires.
Reconnect wiring plug.
1
2
1. Do not remove screw 1
2. Ground wires
3. Green ground wire screw
4. Wiring plug
Style 2
Reconnect wiring plug.
1
1. Do not remove screw 1
2. Wiring plug
5. Replace left hinge cover and screws.
6. Replace the refrigerator door by carefully lifting the door onto
the bottom right hinge.
7. Align and replace the top right hinge as shown (see Graphic
6). Tighten screws.
8. Replace hinge cover and screws. Tighten screws.
9. Plug into a grounded 3 prong outlet.
Door Closing
Your refrigerator has two front adjustable rollers — one on the
right and one on the left. If your refrigerator seems unsteady or if
you want the doors to close more easily, adjust the refrigerator's
tilt using the instructions below:
1. Move the refrigerator into its final position.
2. The two leveling screws are part of the front roller assemblies
which are at the base of the refrigerator on either side (see
Graphic 8).
8
3. Use a hex-head socket wrench to adjust the leveling screws.
4. Open both doors again and check to make sure that they
5. Replace the base grille.
NOTE: Be sure to refasten the Tech Sheet behind the base grille.
Read all directions before you begin.
IMPORTANT: If you turn the refrigerator on before the water line
is connected, turn the ice maker OFF.
Connecting to Water Line
3
4
1. Unplug refrigerator or disconnect power.
2. Turn OFF main water supply. Turn ON nearest faucet long
3. Locate a ½ in. to 1
4. Determine the length of copper tubing you need. Measure
5. Using a grounded drill, drill a
2
6. Fasten the shutoff valve to the cold water pipe with the pipe
7. Slip the compression sleeve and compression nut on the
8. Place the free end of the tubing in a container or sink, and
Turn the leveling screw to the right to raise that side of the
refrigerator or turn the leveling screw to the left to lower that
side. It may take several turns of the leveling screws to adjust
the tilt of the refrigerator (see Graphic 8).
NOTE: Having someone push against the top of the
refrigerator takes some weight off the leveling screws and
rollers. This makes it easier to adjust the screws.
close as easily as you like. If not, tilt the refrigerator slightly
more to the rear by turning both leveling screws to the right. It
may take several more turns, and you should turn both
leveling screws the same amount.
Water Supply Connection
enough to clear line of water.
in. (1.25 cm to 3.18 cm) vertical COLD
water pipe near the refrigerator.
NOTE: Horizontal pipe will work, but drill on the top side of
the pipe, not the bottom. This will help keep water away from
the drill and normal sediment from collecting in the valve.
from the connection on the lower left rear of refrigerator to the
water pipe. Add 7 ft. (2.1 m) to allow for cleaning. Use
(6.35 mm) O.D. (outside diameter) copper tubing. Be sure
both ends of copper tubing are cut square.
you have selected.
1. Cold water pipe
2. Pipe clamp
3. Copper tubing
4. Compression nut
clamp. Be sure the outlet end is solidly in the
in the water pipe and that the washer is under the pipe clamp.
Tighten the packing nut. Tighten the pipe clamp screws
carefully and evenly so washer makes a watertight seal. Do
not overtighten or you may crush the copper tubing.
copper tubing as shown. Insert the end of the tubing into the
outlet end squarely as far as it will go. Screw compression nut
onto outlet end with adjustable wrench. Do not overtighten.
turn ON the main water supply. Flush the tubing until water is
clear. Turn OFF the shutoff valve on the water pipe. Coil the
copper tubing.
in.
in. hole in the cold water pipe
5. Compression sleeve
6. Shutoff valve
7. Packing nut
in. drilled hole