Whirlpool 2262431 사용 및 관리 매뉴얼 - 페이지 6

{카테고리_이름} Whirlpool 2262431에 대한 사용 및 관리 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Whirlpool 2262431 40 페이지. Top-mount refrigerator

페이지 인쇄

4. To determine the length of copper tubing you will need,

measure from connection on lower left rear of refrigerator to

water pipe. Add 7 ft (2.1 m) to allow for moving refrigerator for

cleaning. Use ¹⁄₄ in. (6.35 mm) O.D. (outside diameter) copper

tubing. Be sure both ends of copper tubing are cut square.

5. Using a grounded drill, drill a ¹⁄₄ in. (6.35 mm) hole in the cold

water pipe you have selected.

1. Cold Water Pipe

2. Pipe Clamp

3. Copper Tubing

4. Compression Nut

6. Fasten shutoff valve to cold water pipe with pipe clamp. Be

sure outlet end is solidly in the ¹⁄₄ in. (6.35 mm) drilled hole in

the water pipe and that washer is under the pipe clamp.

Tighten packing nut. Tighten the pipe clamp screws carefully

and evenly so washer makes a watertight seal. Do not

overtighten or you may crush the copper tubing, especially if

soft (coiled) copper tubing is used. Now you are ready to

connect the copper tubing.

7. Slip compression sleeve and compression nut on copper

tubing as shown. Insert end of tubing into outlet end squarely

as far as it will go. Screw compression nut onto outlet end

with adjustable wrench. Do not overtighten.

8. Place the free end of the tubing into a container or sink, and

turn ON main water supply and flush out tubing until water is

clear. Turn OFF shutoff valve on the water pipe. Coil copper

tubing.

Connecting to Refrigerator:

NOTE: The first step for connecting the water line to your

refrigerator is different depending on the type of water valve

provided with your refrigerator. See the diagrams below to

determine the style of valve you have. (On kit models, assemble

water valve to refrigerator per kit instructions.)

1. For Style 1, disconnect the tube clamp on the back of the

product and insert the copper tubing through the clamp, as

shown. Remove the tape label from the valve inlet and insert

copper tubing until it bottoms out (approximately ³⁄₄ in.

[1.9 cm]). Tighten nut by hand as much as possible; then turn

the nut an additional ¹⁄₂ turn using a wrench. Do not

overtighten. Reattach the tube clamp and tube to the back of

the cabinet. Skip to Step 2.

For Style 2, disconnect the tube clamp on the back of the

product and insert copper tubing through the clamp as

shown. Attach the copper tube to the valve inlet using a

compression nut and sleeve as shown. Tighten the

compression nut. Do not overtighten. Reattach the tube

clamp and tube to the back of the cabinet. Move to Step 2.

5. Compression Sleeve

6. Shutoff Valve

7. Packing Nut

Style 1

1. Tube Clamp

2. Copper Tubing

Style 2

1. Tube Clamp

2. Copper Tubing

2. Turn shutoff valve ON. Check for leaks. Tighten any

connections (including connections at the valve) or nuts that

leak.

3. The ice maker is equipped with a built-in water strainer. If

local water conditions require periodic cleaning or a well is

your source of water supply, a second water strainer should

be installed in the ¹⁄₄ in. (6.35 mm) water line. Obtain a water

strainer from your nearest appliance dealer. Install at either

tube connection.

4. Plug in refrigerator or reconnect power.

Refrigerator Doors: Removing, Reversing

(optional) and Replacing

TOOLS NEEDED: ⁵⁄₁₆ in. hex-head socket wrench, No. 2 Phillips

screwdriver, flat-head screwdriver, ⁵⁄₁₆ in. open-end wrench, flat

2 in. putty knife.

IMPORTANT:

Before you begin, turn the refrigerator control OFF and

unplug refrigerator or disconnect power.

Remove food and any adjustable door or utility bins from

doors.

If you are only removing and replacing the doors, see the

"Door and Hinge Removal" and "Door and Hinge

Replacement" sections.

Depending on your model, you may have standard (Style 1)

or contour (Style 2) doors. If you are also going to reverse the

door swing, follow the instructions for the appropriate door

style.

3. Compression Nut

4. Valve Inlet

3. Compression Nut