Whirlpool WRX988SIBW 설치 지침 및 사용 설명서 - 페이지 6

{카테고리_이름} Whirlpool WRX988SIBW에 대한 설치 지침 및 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Whirlpool WRX988SIBW 48 페이지. Bottom mount refrigerator
Whirlpool WRX988SIBW에 대해서도 마찬가지입니다: 에너지 매뉴얼 (1 페이지)

페이지 인쇄

3. Disconnect the wiring plug located on top of the door hinge.

Grasp each side of the wiring plug. With your left thumb,

press down to release the catch and pull the sections of

the plug apart.

NOTE: Do not remove the green, ground wire. It should

remain attached to the door hinge.

4. Using the

" hex key wrench, remove the two internal hex

head screws from the top hinge, and set aside.

NOTES:

Provide additional support for the refrigerator door while

the hinges are being removed. Do not depend on the door

gasket magnets to hold the door in place while you are

working.

Do not remove the two locator screws. These screws will

help you align the hinge when you replace the door.

" Internal hex head screws

B. Ground wire (do not remove)

5. Lift the refrigerator door from the bottom hinge pin. The top

hinge will come away with the door.

NOTE: It may not be necessary to remove the bottom hinges

and brake feet assemblies to move the refrigerator through a

doorway.

Only if necessary, use a driver with a #2 square bit tip to

remove the bottom hinges and a

the brake feet screws.

Replace Right-Hand Refrigerator Door

1. Set the right-hand door onto the bottom hinge pin.

2. Insert the top hinge pin into the open hole in the top of the

refrigerator door.

3. Using the two

" internal hex head screws, fasten the hinge

to the cabinet. Do not tighten the screws completely.

Replace Left-Hand Refrigerator Door

IMPORTANT: Do not intertwine the water tubing and wiring

bundles when reconnecting them.

1. Set the left-hand door onto the bottom hinge pin.

2. Using the two

" internal hex head screws, fasten the hinge

to the cabinet. Do not tighten the screws completely.

C. Locator screws (do not

remove)

" nut driver to remove

3. Reconnect the water dispenser tubing.

Style 1 - Insert the tubing into the fitting until it stops and the

outer ring is touching the face of fitting.

Style 2 - Insert the tubing firmly into the fitting until it stops.

Close the clasp around the tubing. The clasp snaps into place

between the fitting and the collar.

4. Reconnect the electrical wiring.

Push together the two sections of the wiring plug.

Final Steps

1. Completely tighten the four internal hex head screws (two on

the right-hand door hinge and two on the left-hand door

hinge).

2. Replace both top hinge covers.

Remove and Replace Drawer Fronts

Depending on the width of your door opening, it may be

necessary to remove the drawer fronts to move the refrigerator

into your home.

IMPORTANT:

If the refrigerator was previously installed and you are moving

it out of the home, before you begin, turn the refrigerator

control OFF, and unplug the refrigerator or disconnect power.

Remove food from the drawers.

Two people may be required to remove and replace the

drawer fronts.

Tools Needed:

" Hex head nut driver, Flat-blade screwdriver

Refrigerated Drawer

Disconnect Wiring

NOTES:

The exterior refrigerator drawer front is connected to the

temperature control. Before removing the drawer front, the

wires must be disconnected from the temperature control.

The cable visible behind and under the pantry drawer at the

right side contains wiring for the pantry control and moves

with the drawer as it is pulled out. There is no need to

disconnect this cable.

1. Open the drawer to its full extension, and remove the large

interior bin.

2. Locate the wiring cover on the backside of the drawer front.

Press tab on the cover to release the snaps, and pull off cover

to reveal the wiring connection.

A. Press tab

B. Wiring connection cover