Whirlpool WSR57R18DM02 사용자 설명서 - 페이지 7

{카테고리_이름} Whirlpool WSR57R18DM02에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Whirlpool WSR57R18DM02 13 페이지.

페이지 인쇄

Refrigerator Leveling and Door Closing

Your refrigerator has two front adjustable legs — one on each

side. The back of the refrigerator rests on two fixed rollers. The

base grille covers the adjustable brake feet and roller assemblies

located at the bottom of the refrigerator below the refrigerator

door. Before making any adjustments, remove the base grille and

move the refrigerator to its final location.

Tools Needed: 1/4" hex driver, Phillips head screwdriver

1. Remove the base grille screws. Grasp the grille firmly and

pull it toward you. Open the refrigerator door to access the

brake feet.

NOTE: To allow the refrigerator to roll more easily, raise the

brake feet by turning them counterclockwise. The front roll-

ers will be touching the floor.

2. Move the refrigerator to its final location.

3. Lower the brake feet, by turning them clockwise, until the

rollers are off the floor and both brake feet are snug against

the floor. This keeps the refrigerator from rolling forward

when you are opening the refrigerator door.

IMPORTANT: If you need to make further adjustments

involving the brake feet, you must turn both brake feet the

same amount to keep the refrigerator level.

4. Make sure the door closes easily. If you are satisfied with the

door opening and closing, skip the next section. If, however,

the door does not close easily or the door pops open, adjust

the tilt.

To Adjust the Cabinet Tilt:

NOTE: Having someone push against the top of the refrigerator

takes some weight off the brake feet. This makes it easier to turn

them.

Open the refrigerator door. Use a 1/4" hex driver to turn both

■

brake feet clockwise the same amount. This will raise the

front of the refrigerator. It may take several turns to allow the

door to close more easily.

A. Brake foot

B. Front roller

C. 1/4" hex driver

5. Make sure the refrigerator is steady. If the refrigerator seems

To Steady the Refrigerator:

■

6. Replace the base grille by aligning the ends of the grille with

Normal Sounds

Your new refrigerator may make sounds that your old one didn't

make. Because the sounds are new to you, you might be

concerned about them. Most of the new sounds are normal.

Hard surfaces, like the floor, walls, and cabinets, can make

the sounds seem louder. The following describes the kinds of

sounds and what may be making them.

■

unsteady or rolls forward when the door is pulled open,

adjust the brake feet.

Open the refrigerator door. Using a 1/4" hex driver, turn

both brake feet clockwise the same amount until the brake

feet are snug against the floor. Check again. If not satisfied,

continue to adjust the brake feet by half turns of the screw

until the refrigerator does not roll forward when the door is

opened.

the leveling assemblies on each side and snapping the grille

into place. Reinstall the Phillips screws.

Your refrigerator is designed to run more efficiently to keep

your food items at the desired temperatures and to minimize

energy usage. The high-efficiency compressor and fans may

cause your refrigerator to run longer than your old one. You

may also hear a pulsating or high-pitched sound from the

compressor or fans adjusting to optimize performance.

You may hear the evaporator fan motor circulating air

through the refrigerator compartment. The fan speed may

increase as you open the doors or add warm food.

Rattling noises may come from the flow of refrigerant or

items stored on top of the refrigerator.

Water dripping on the defrost heater during a Defrost cycle

may cause a sizzling sound.

As each cycle ends, you may hear a gurgling sound due to

the refrigerant flowing in your refrigerator.

Contraction and expansion of the inside walls may cause a

popping noise.

You may hear air being forced over the condenser by the

condenser fan.

You may hear water running into the drain pan during the

Defrost cycle.