Whirlpool WED7500VW 사용 및 관리 매뉴얼 - 페이지 15

{카테고리_이름} Whirlpool WED7500VW에 대한 사용 및 관리 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Whirlpool WED7500VW 20 페이지. Compact electric dryer with 11 cycles
Whirlpool WED7500VW에 대해서도 마찬가지입니다: 사양 (8 페이지), 사용 및 관리 매뉴얼 (20 페이지), 치수 및 설치 정보 (1 페이지), 사용 설명서 (8 페이지), 설치 지침 (2 페이지)

페이지 인쇄

Controls

The control panel is simple to understand and easy to operate.

The illustrations below define the knobs and buttons, and the

paragraphs define the purpose of each.

Power

This button switches the power to the machine on and off. The

indicator light will glow to indicate the power is on.

Indicator Light

This light indicates when the power is on or that a cycle has

started.

Temperature

The Temperature Control button lets you select between a normal

and low drying temperature.

NOTE: Always refer to the care label on the garment to determine

whether it can be tumble dried.

Normal

The Normal temperature setting is for sturdy fabrics, such as

cotton, linen and denim. If the Temperature Control button is not

pressed in, the temperature setting is Normal.

Low

The Low setting is for synthetics, such as cotton/polyester blend,

rayon, acetate, washable silk or nylon. If the Temperature Control

button is pressed in, the temperature setting is Low.

Cycle Knob

Turn this knob to the recommended setting. Indicator light will

flash to indicate a cycle has been selected. See "Drying, Cycle

and Temperature Tips."

Stop Position

Turn the cycle knob to the Stop position at any time.

Start Button

After you have selected a cycle and temperature, press this

button to start the cycle. Indicator light will glow to indicate the

cycle has started.

Drying, Cycle and Temperature Tips

Select the correct cycle and temperature for your load.

Your dryer tumbles the load without heat during the last few

minutes of all cycles to make the load easier to handle and to

reduce wrinkling. After the cool-down cycle ends, the light

flashes, and an end-of-cycle signal sounds to indicate the cycle

is complete.

Drying tips

Follow care label directions when they are available.

Remove the load from the dryer as soon as tumbling stops to

reduce wrinkling. This is especially important for permanent

press, knits and synthetic fabrics.

Avoid drying heavy work clothes with lighter fabrics. This

could cause overdrying of lighter fabrics, leading to increased

shrinkage or wrinkling.

Cycle and temperature tips

Dry most loads using an automatic cycle.

Line dry bonded or laminated fabrics.

NOTE: If you have questions about drying temperatures for

various loads, refer to the care label directions.

Automatic Cycles

When you are using the Auto Moisture Sensing Cycle, two metal

strips (sensors) located on the dryer baffles determine the

dryness of the load. The metal strips help detect the amount of

moisture left in the clothes as they pass. When there is moisture

left in the clothes, the machine will continue to run. As clothes

begin to dry, the amount of water left in the clothes decreases,

and the timer advances through the remainder of the cycle. When

the selected dryness level is reached, the dryer goes into a cool

down period of up to 15 minutes.

Automatic cycles may be used for most loads. Automatic cycles

give the best drying results in the shortest time. Drying time

varies according to the type of fabric, size of the load, and

dryness setting.

After drying a load, check the dryness.

If the load is drier than you like, select a setting closer to Less

Dry the next time you dry a similar load.

If a load is not as dry as you like, complete drying using a

Timed cycle. Select a setting closer to More Dry the next time

you dry a similar load.