Whirlpool WGD94HEXL 사용 및 관리 매뉴얼 - 페이지 17

{카테고리_이름} Whirlpool WGD94HEXL에 대한 사용 및 관리 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Whirlpool WGD94HEXL 40 페이지. Electronic dryer
Whirlpool WGD94HEXL에 대해서도 마찬가지입니다: 사용 설명서 (8 페이지)

페이지 인쇄

First try the solutions suggested here or visit our website at www.whirlpool.com/help

If you experience

Dryer Results (cont.)

Odors

Load too hot

Dryer Displaying Code Message

"PF" (power failure)

"L2" Diagnostic Code

(low or no line voltage

condition)

"AF" (low airflow

condition)

"F# E#" (F1 E1, F3 E1, etc.)

variable service codes.

for assistance and to possibly avoid a service call.

Possible Causes

Recent painting, staining, or

varnishing in the area where your

dryer is located.

For steam cycles, the water is not

properly connected with the dryer.

Odors are left in garments after

wearing.

Load removed before cooldown

portion of cycle complete.

Using Timed Dry cycle with a high

temperature setting.

The drying cycle has been

interrupted by a power failure.

There may be a problem with your

home power supply keeping the

dryer's heater from turning on.

The lint screen or vent is clogged;

the vent is crushed or kinked or

has too many turns.

The dryer is in need of service.

Ventilate the area. When the odors or fumes are gone from

the area, rewash and dry the clothing.

Make sure water is connected to the dryer. Check that water

inlet hose is connected to both the faucet and dryer's water

inlet valve. Check that the water supply is turned on.

To remove odors left in garments after wearing, select Quick

Refresh for small loads of up to 9 garments. This cycle is

best for reducing wrinkles and odors from loads consisting of

wrinkle-free cotton, cotton polyester blends, common knits,

and synthetics.

Allow the dryer to complete the cooldown portion of the cycle

before removing the load.

Select an Auto Dry cycle with a lower heat setting to avoid

overdrying the load.

Press and hold START to restart the dryer.

The dryer will continue to run when this diagnostic code is

present. Press any key to clear the code from the display and

return to the estimated time remaining.

Try the following:

Check to see if a household fuse has blown or circuit breaker

has tripped. Electric dryers use two household fuses or

breakers. Replace the fuse or reset the circuit breaker.

Confirm the power cord is properly installed. Refer to

the Installation Instructions for details.

Select a Timed Dry heated cycle, and restart the dryer.

If the message persists, consult a qualified electrician.

The dryer will continue to run when this diagnostic code is

present. Press any key to clear the code from the display and

return to the estimated time remaining.

Try the following:

• Clean lint screen.

• Check to see if the vent run from the dryer to the wall is

crushed or kinked.

• Confirm the vent run from the dryer to the wall is free of lint

and debris.

Confirm the exterior vent exhaust hood is free of lint and debris.

Confirm your vent system falls within the recommended run

length and number of elbows for the type of vent you are using.

Refer to "Plan Vent System" in the Installaton Instructions for

details.

Select a Timed Dry heated cycle, and restart the dryer.

If the message persists, have your entire home venting run

cleaned.

If a code beginning with an "F" appears in the display.

Alternating between F# and E#, the dryer control has

detected a problem that requires service. Call for service.

Solution