Whirlpool 3395314 설치 지침 매뉴얼 - 페이지 7
{카테고리_이름} Whirlpool 3395314에 대한 설치 지침 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Whirlpool 3395314 12 페이지. Coin-operated stacked dryer
페이지 인쇄
f
internal
exhaust duct
6. Insert elbow
end of duct pieces
through
the side opening.
Reach
through
the access
panel opening
and attach
elbow
to the internal
exhaust
duct. Check
the length of
straight
duct extending
out the side
of the cabinet.
If duct extends
too far
to make the exhaust
duct
connection,
mark a line around
the
straight
duct one inch out from the
cabinet.
Remove
the duct and elbow
and cut the straight
pipe to the
length
needed.
Reinsert the duct
pieces.
Use duct tape
to connect
the
elbow
to the internal
exhaust
duct.
Repeat
for the other dryer.
7. Insert the plastic cover into the
rear exhaust
opening.
8.
Replace
the access
panels.
9. Use duct tape to seal all joints.
To connect exhaust duct
through the bottom of the
lower dryer only -
Note: You must use a three-section
elbow
to connect
exhaust
duct
through
the bottom
of the lower
dryer.
1.
Check
that the legs extend
one
inch from the bottom
of the dryer.
2. Remove
the lower dryer access
panel
by releasing
the two locking
clips with a small, flat-blade
screwdriver.
The clips are located
four inches in from each
side of the
access
panel,
Lift access
panel
off
the bottom
clips and set aside.
3. Remove
duct tape f
m internal
exhaust
duct and the s
t
aight duct.
4. Remove
the screw fr m the duct
clip that attaches
the s aight duct to
the back of the cabine
Depress the
clip and remove
the str
using a twisting
motion
1
ight duct
rough the
rear exhaust
opening.
i
5. Measure
from the
straight duct and mark
Cut the straight duct
6.
Reach through
the r
opening
and depress c
on one of the side,
covers.
Remove
the co
7. With a Phillips screw
river, reach
through
the rear exhau
opening
and remove
the screw
%
at attaches
the cover to the dryer
se. Carefully
remove
the cover and
rew through
the rear exhaust
openin
.
Floor Damage
Slide dryers onto cardboard
or
hardboard betore moving across
tloor.
Failure to do so may cwse damage
to tloor coverlng.
8.
Move dryers into
position.
Reach throug
opening
and mark the
9. Cut opening
through
the floor.
10.
Push the four-inch,
straight duct
through
the rear exhaust
opening
and onto the internal
duct as far as it
will go.
+
a
front
L3
Of
I
dryer
I.--
1 1.
Insert the elbow
through
the rear
exhaust
opening.
Insert elbow
into
the bottom
exhaust
opening.
/iah
I I I L--
of
dryer
12. Slide the straight
duct into the
elbow
approximately
one inch.
Use
duct tape to seal both Jolnts.
screw head
(fastens
against
edge of cabinet)-
cabinet
rear
13.
Insert the
bottom
exhaust
cover through
the
side exhaust
opening.
Put the
cover over the rear
c
tab
exhaust
opening
bottom
with the tab
of dryer
pointing
down to
bottom
of dryer.
t
Insert screw through
the hole in the cover that is on the
inside of the cabinet.
Tighten screw.
14. Replace
the side exhaust
cover.
15. Move the dryers into operating
position.
Check
that the elbow
is
through
the bottom
exhaust
opening.
Replace
the access
panel.
16.
Connect
elbow
to exhaust
duct.
Then connect
exhaust
duct to
exhaust
hood or main exhaust.
Use
duct tape to seal all joints.
Page 7