Whirlpool 3LG5701XP 설치 지침 - 페이지 2

{카테고리_이름} Whirlpool 3LG5701XP에 대한 설치 지침을 온라인으로 검색하거나 PDF를 다운로드하세요. Whirlpool 3LG5701XP 5 페이지. Automatic dryers
Whirlpool 3LG5701XP에 대해서도 마찬가지입니다: 사용 및 관리 매뉴얼 (12 페이지)

페이지 인쇄

. Replace all access or sewice panels

before operating

dryer

Before you start...

Mark an X across the letter or number

as you complete

each step

You need these tools to i

screwdriver

install the dryer...proper

installation

Your responsibility

FOR YOUR SAFETY

If you smell gas:

1. Open windows

2. Don't touch electrical

switches

3. Extinguish

any open flame

4. Immediately

call your gas

supplier.

FOR YOUR SAFETY

Do not store or use gasoline

or other flammable

vapors and

liquids

in the vicinity

of this or

any other appliance.

Make sure you

have everything

necessary for proper instillation.

You'll need:

To meet code

requirements:

some

codes keep from or limit installation

clothes dryers in garages, closets,

mobile homes and sleeping quarters

[Check with your local Dullding

inspector.)

Important:

observe

all governing

codes

and ordinances.

To check utilities:

proper gas and

electric supply connections

should

be available.

To check exhaust

requirements:

a four inch metal exhaust duct IS

recommended.

LOCATION

Max.

423/a"

Size: Must be large enough to fully

open dryer door. For recessed or closet

installation

spacing see panel B

Support:

The floor must be able to

suppod the appliance

weight of 175

pounds.

Level floor: Maximum

floor slope

under dryer - 1 inch,

Protection

from the weather:

Proper

operation

of dryer cycles requires

temperatures

above 45' F., or the dryer

may not shut off when automatic

cycles

ore used

WARNING:

It is the personal responsibility

of the

customer to ensure that gasoline,

paint, thinners and other flammable

materials are not used or stored near

the dryer. Fumes from these materials

could result In fire or explosion

Never install the dryer up against

draperies or curtains or on carpet and

be sure to keep any and all items from

falling or collecting

behind the dryer,

This appliance

is suitable

for mobile

home installations.

For Mobile Home use, this appliance

MUST be fastened to the floor and

MUST be exhausted to the outside.

Order Mobile Home Installation

Kit

No. 346765 from your WhIrlpool dealer.

Kit includes the necessary fastening

hardware

and detailed

installation

instructions

Exhaust system hardware

also avallable

through your WhIrlpool

dealer.

Input ratings shown on the rating plate

(senal

tag)

are for elevattons up to

2,000 feet For elevations above 2,000

feet, ratings should be reduced

at a

rate of 4% for each 1,000 feet above

sea level.

Gas supply

requirements

OBSERVE ALL GOVERNING

CODES

AND ORDINANCES

First make certain

that this dryer IS

equipped

with the corkect burner for

the particular

type of gas in the home.

Burner information

will be found on

the rating plate in door well of the

appliance.

If this information

does not

agree with the type of gas available,

see your dealer,

This dryer is equipped

for use with

NATURAL GAS. You may use

manufactured,

mixed and L.P gases

with appropriate

conversion.

attempt shall be made to convert the

appliance

from the gas specified

on the rating plate for use with a

different gas wlthout consulting

the

serving gas supplier. Conversion

must

be done by a qualified

service

technician

Provide a gas supply line

to the dryer location. When

rlgid pipe

used it'should be % inch IPS

When acceptable

to the gas supplier,

s/s inch approved

tubing may be used

for lengths under 20 feet. For lengths

over 20 feet, larger tubing should be

used Pipe joint compounds

resistant to

the action of LP gas must be used

The supply line should be equipped

with a shut-off valve This valve should

be located

in the same room as the

dryer and should be in a location

that

allows ease of opening

and closing

Do not block access to shut-off valve.

If the dryer is installed in a confined

area such as a bedroom,

bathroom

or closet, it must be exhausted

the outside and provlsion made for

enough air for combustion

and

ventilation

(Check governing

codes

and ordinances

) Also refer to the

section of this instruction covering

Recessed or Closet Installations.

If I

permit, it Is

recommended

that flexible metal

tubing be used for connecting

the

appliance

to the gas supply line. (The

gas pipe which extends through the

lower rear of the appliance

has yg Inch

male pipe thread.)

If rigid pipe IS used

H as a gas supply line,

a combinationof

pip& fittings

must be used to obtain an in-line

connection

to the dryer.

Make sure the

lower edaes of the

cabinet,

plus the bvack and bottom

sides of the dryer are free of

obstructions

to permit adequate

clearance

of air openings

for

combustion

air

For ease of Installation,

H operation

and servicing

(if ever needed]

adequate

space

should be provided

around the dryer

A '/1 inch NPT

plugged

tapplng,

accessible

for test gage connection,

must be installed immediately

upstream of the gas supply connectlon

io the dryer.

The dryer and its lndivldual

shut-off

valve must be disconnected

from the

gas supply piping system during any

pressure testing of that system at test

pressures in excess of % psig (3.45 kPa).

The dryer must be isolated from the

gas supply piping system by closing its

indlvldual

manual shut-off valve during

any pressure testing of the gas supply

piping system at test pressures equal

to or less ihan ;', pslg (3.45 kPa)

Important:

observe

all governing

codes

and ordinances.

The dryer shut-off valve and

the wirina diaaram

are

located

behlnd the low'er front access

panel. To open the access panel,

grasp the sides of the panel at the top

and pull out and down. The panel is

hinged at the bottom

Close the

access panel after sewicing.

Do not

operate the dryer with the access

panel open.

If dryer will not operate, check

the followlna

to be sure that:

I. Electric supply iiconnected

2 Fuse is intact and tight.

3 Door

closed

4 Controls ore set in a running or

"On" position

5 Start button has been pushed

firmly or the power control lever

moved upward

to start

6 Gas shut-off valves ore open both

on drver and on sur)r)lv lines.

Panel