Whirlpool 3RAWZ481G 설치 지침 매뉴얼 - 페이지 8

{카테고리_이름} Whirlpool 3RAWZ481G에 대한 설치 지침 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Whirlpool 3RAWZ481G 25 페이지. Electric and gas dryer
Whirlpool 3RAWZ481G에 대해서도 마찬가지입니다: 사용 및 관리 매뉴얼 (24 페이지), 사용 및 관리 매뉴얼 (28 페이지)

페이지 인쇄

Determine Vent Length

better

1. Select the route that will provide the

straightest and most direct path

outdoors. Plan the installation to use the

fewest number of elbows and turns.

When using elbows or making turns,

allow as much room as possible. Bend

vent gradually to avoid kinking. Avoid

90° turns.

2. Determine vent length.

The maximum length of the exhaust

system depends upon:

• The type of vent (rigid metal or flexible

metal).

• The number of elbows used.

• The type of hood.

box

hood

10.2 cm

(4")

louvered

hood

angled

hood

10.2 cm

(4")

10.2 cm

(4")

recommended

hood styles

See the exhaust vent length chart that

matches your hood type for the

maximum vent lengths you can use.

Exhaust systems longer than specified

will:

• Shorten the life of the dryer.

• Reduce performance, resulting in

longer drying times and increased

energy usage.

3. Determine the number of elbows you will

need.

IMPORTANT: Do not use vent runs longer

than those specified in the Vent Length

Chart.

The following chart helps you determine

your maximum vent length based on the

number of 90° turns or elbows you will

need and the type of vent (rigid or flexible

metal) and hood that you will use.

Vent Length Chart

Number of

90° turns or

elbows

good

NOTE: Side and bottom exhaust

installations have a 90° turn inside the

dryer. To determine maximum exhaust

length, add 1 90° turn to the chart.

Now start installation

Install vent system

6.4 cm

(2-1/2")

1. Install exhaust hood. Use caulking

compound to seal exterior wall opening

acceptable style

around exhaust hood.

2. Connect vent to exhaust hood. Vent

must fit inside exhaust hood. Secure

vent to exhaust hood with 10.2 cm (4 in.)

clamp.

3. Run vent to dryer location. Use the

straightest path possible. See

"Determine Vent Length." Avoid 90°

turns. Use clamps to seal all joints. Do

not use duct tape, screws or other

fastening devices that extend into the

interior of the vent to secure vent.

Type of

Box or

Angled

metal vent

Louvered

hoods

rigid

20 m

17.7 m

(64 ft.)

(58 ft.)

flexible

11 m

8.5 m

(36 ft.)

(28 ft.)

rigid

16.5 m

14.6 m

(54 ft.)

(48 ft.)

flexible

9.4 m

7 m

(31 ft.)

(23 ft.)

rigid

13.4 m

11.6 m

(44 ft.)

(38 ft.)

flexible

8.2 m

5.8 m

(27 ft.)

(19 ft.)

rigid

10.7 m

8.8 m

(35 ft.)

(29 ft.)

flexible

7.6 m

5.2 m

(25 ft.)

(17 ft.)

rigid

8.2 m

6.4 m

(27 ft.)

(21 ft.)

flexible

7 m

4.6 m

(23 ft.)

(15 ft.)

Install leveling legs

WARNING

Excessive Weight Hazard

Use two or more people to move and

install dryer.

Failure to do so can result in back or

other injury.

1. To protect the floor, use a large flat

piece of cardboard from the dryer

carton. Place cardboard under the entire

back edge of the dryer. See illustration.

2. Firmly grasp the body of the dryer (not

the console panel).

Gently lay the dryer on the cardboard.

3. Examine the leveling legs. Find the

diamond marking.

4. Screw the legs into the leg holes by

hand. Use a wrench to finish turning the

legs until the diamond marking is no

longer visible.

5. Place a carton corner post under each

of the 2 dryer back corners. Stand the

dryer up. Slide the dryer on the corner

posts until it is close to its final location.

Leave enough room to connect the

exhaust vent or gas line.

6. Once connection is made and dryer is in

final location, remove corner posts and

cardboard.