Whirlpool 7MWGD6605MW 사용 및 관리 매뉴얼 - 페이지 28

{카테고리_이름} Whirlpool 7MWGD6605MW에 대한 사용 및 관리 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Whirlpool 7MWGD6605MW 41 페이지. Electric dryer / gas dryer

페이지 인쇄

completely. This option is available on some cycles.

The Damp Dry signal is selected as a default for the

Bulky Items/Normal, Bulky Items/Wrinkle Control,

and Bulky Items/Heavy Duty cycles, as a reminder

to manually reposition bulky loads midway through

the cycle.

Reduce Static (on some models)

Touch to add the Reduce Static option to selected

Automatic cycles. The dryer will automatically tumble,

pause, and introduce a small amount of moisture

into the load to help reduce static. This option adds

approximately 3 minutes to the total cycle time.

Control Lock

Use this option to lock the controls of the dryer

and avoid an accidental change in cycle options

or preferences during a drying cycle.

Touch and hold CONTROL LOCK or DAMP DRY

SIGNAL (depending on the model) for 3 seconds to

lock or unlock the controls of the dryer. During this

time, the LED Display will count down "3-2-1."

Once the controls are locked, the LED Display

will display "Loc."

NOTE: The Control Lock function may be enabled

when recovering from a power failure. To unlock the

control, touch and hold CONTROL LOCK or DAMP

DRY SIGNAL (depending on the model) for at least

3 seconds.

EcoBoost Option

The EcoBoost option will default on only for the

Regular/Normal cycle and is only available on

that cycle. This option allows you to increase your

energy savings by using a slightly lower heat level.

The EcoBoost option will increase drying times by

approximately 40 minutes, which will be reflected

on the LED Display. If optimal time is desired, touch

ECOBOOST to turn off this option.

LED DISPLAY

When you select a cycle, its default settings will light up

and the Estimated Time Remaining (for Automatic Cycles)

will vary depending on "What to Dry" and "How to Dry"

selections, or actual time remaining for Timed Dry cycles

(for Manual Cycles) will be displayed.

CYCLE STATUS INDICATORS

Appearance may vary.

The Cycle Status Indicators show the progress of a cycle.

Not all indicators are available on all models.

Sensing

The Sensing indicator will light periodically during Sensor

Cycles to indicate that the moisture sensor on the dryer is

operating. This indicator will not light during Timed Cycles

or options such as Wrinkle Shield.

Wet

The load is still wet and/or the cycle just started.

Damp

This indicator shows that the load is partially dried and

items that you may wish to hang up or iron while still

damp may be removed.

Cool Down

The dryer has finished drying with heat and is now

tumbling the load without heat to cool it down.

Check Vent

The Check Vent indicator is a feature available for

Automatic cycles only. This indicator will show the status

of airflow through the dryer and the dryer vent system

for the dryer's life. During the sensing phase at the

beginning of the cycle, the Check Vent light will come on

if a blocked vent or low airflow issue is detected. This light

will stay on for the entire cycle. Should the Check Vent

light illuminate, refer to the "Troubleshooting" section

for potential solutions to the issue.

The light will be cleared upon completion of the cycle,

touching Power, or opening the door. The Check Vent light

will continue to illuminate during the cycle unless the root

cause is resolved.

REMEMBER: The dryer will continue to operate even

while the indicator is lit, but poor airflow can impact dry

times and overall performance. For more information on

maintaining good airflow, see "Check Your Vent System

for Good Airflow."

NOTE: If there are other error issues during a cycle,

the Check Vent indicator will not light up. See the

"Troubleshooting" section.

End

This will indicate that the selected cycle has ended

and the load may be removed from the dryer. If Wrinkle

Shield has been selected, the dryer may continue to

tumble the load, even if "End" is displayed.

Control Lock

This will illuminate once the controls are locked.

STEAM REFRESH CYCLE (steam models only)

This cycle is best for reducing wrinkles and odors from

dry items. Cycle time will increase, depending on number

of items. This is an independent cycle that cannot be

combined with any other cycle.