Whirlpool 8578198 사용 및 관리 매뉴얼 - 페이지 4

{카테고리_이름} Whirlpool 8578198에 대한 사용 및 관리 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Whirlpool 8578198 28 페이지. 120-volt electric compact dryer

페이지 인쇄

Tools and Parts

Tools needed

Gather the required tools and parts before starting installation.

Read and follow the safety instructions provided with any tools

listed here.

Flat-blade screwdriver

Level

Adjustable wrench

Vent clamps

Parts supplied

Remove parts package from the dryer drum. Check that all parts

listed are included.

1 - Cycle Control (timer)

knob

1 - Push to Start button

4 - casters

Parts needed

Check local codes, existing electrical supply and venting, and

see "Venting Requirements" and "Electrical Requirements"

before purchasing parts.

Mobile home installations require metal exhaust system

hardware

Permanent installations require 4 dryer feet

For ordering information, please reference the "Assistance or

Service" section of this manual. You can also contact the dealer

from whom you purchased your dryer.

Location Requirements

WARNING

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from dryer.

Place dryer at least 18 inches (46 cm) above the floor

for a garage installation.

Failure to do so can result in death, explosion, or fire.

You will need

A location that allows for proper exhaust installation. See

"Venting Requirements."

A 120-volt, 60-hz., AC-only, 15- or 20-amp circuit.

INSTALLATION INSTRUCTIONS

Caulking gun and

compound (for installing

new exhaust vent)

Tin snips (new vent

installations)

2 - cord brackets

2 - screws

A grounded electrical outlet located within 2 ft (61 cm) of

either side of the dryer. See "Electrical Requirements."

A sturdy floor to support the dryer weight (dryer and load) of

115 lbs (52 kg). The combined weight of a companion

appliance should also be considered.

A level floor with a maximum slope of 1" (2.5 cm) under entire

dryer.

Do not operate your dryer at temperatures below 45ºF (7ºC). At

lower temperatures, the dryer might not shut off at the end of an

automatic cycle. Drying times can be extended.

The dryer must not be installed or stored in an area where it will

be exposed to water and/or weather.

Check code requirements. Some codes limit, or do not permit,

installation of the dryer in garages, closets, mobile homes, or

sleeping quarters. Contact your local building inspector.

Installation Clearances

The location must be large enough to allow the dryer door to

open fully.

Dryer Dimensions

†Height with caster is 32½" (82.6 cm)

*Most installations require a minimum 5½" (14.0 cm) clearance

behind the dryer for the exhaust vent with elbows. See "Venting

Requirements."

Minimum installation spacing for recessed area and closet

installation

The following dimensions shown are for the minimum spacing

allowed when the unit is to be operated with, or without, the

Stack Stand Kit. To purchase a Stack Stand Kit, see "Assistance

or Service."

Additional spacing should be considered for ease of

installation and servicing.

Additional clearances might be required for wall, door, and

floor moldings.

Additional spacing of 1" (2.5 cm) on all sides of the dryer is

recommended to reduce noise transfer.

For closet installation with a door, minimum ventilation

openings in the top and bottom of the door are required.

Louvered doors with equivalent ventilation openings are

acceptable.

Companion appliance spacing should also be considered.

(52.7 cm)

31"

†

(78.7 cm)

(60.6 cm)