Whirlpool 859991624900 빠른 매뉴얼 - 페이지 4

{카테고리_이름} Whirlpool 859991624900에 대한 빠른 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Whirlpool 859991624900 12 페이지.

Quick guide

TROUBLESHOOTING

THANK YOU FOR BUYING A WHIRLPOOL PRODUCT.

In order to receive a more complete assistance,

Before contacting the After-sales Service, refer to the table below. Often the malfunctions are minor and can be solved in few

please register your product on

minutes.

www.whirlpool.eu/register

Malfunction

Possible cause

PLEASE SCAN THE QR CODE ON YOUR APPLIANCE IN ORDER TO REACH MORE INFORMATION.

The drying

An appropriate maintenance was not carried out. Refer to the Cleaning & Maintenance section and perform the

times are very

long.

The garments are too wet.

Room temperature.

The programme, the time and/or the drying level

set are not suitable for the type and the amount

of load inserted into the dryer.

The dryer may be overloaded.

The tumble

The "On/Off " button was not pressed.

dryer does not

The plug is not inserted into the socket.

turn on.

The socket is faulty.

A power failure occurred.

The tumble

The door has not been closed properly.

dryer does not

A time delay was set to the start of the cycle.

start.

The "Start/Pause" button was not pressed.

The Key Lock function was enabled (for machines

equipped with this option).

Garments are

wet at cycle

Small load.

completion.

Large loads or heavier fabrics.

The drying cycle was paused and then not

reactivated within 15 minutes, causing the

machine to shut down.

A power failure might have occurred, causing the

machine to shut down.

Lights on or fl ashing

Water tank

The water tank is full.

Door fi lter

Failure of the air fl ow necessary for machine

operation.

Bottom fi lter*

The bottom fi lter requires cleaning.

The presence

of wrench

symbol signals a

malfunction.

The machine sensors detected a failure.

*Note: some models are auto-cleaning and not equipped with bottom fi lter. Please refer to the Cleaning & Maintenance section.

Policies, standard documentation, ordering of spare parts and additional product information can be found by:

• Using QR code in your appliance

• Visiting our website docs.whirlpool.eu and parts-selfservice.whirlpool.com

• Alternatively, contact our After-sales Service (See phone number in the warranty booklet). When contacting our After-sales

Service, please state the codes provided on your product's identification plate.

Before using the appliance carefully

read the Safety Instruction.

Solution

operations described.

Carry out a washing cycle with higher spin speed to remove as much

water as possible.

The drying time may be longer if the room temperature falls outside

the 14–30°C range.

Refer to Programmes and Options sections to fi nd the programme

and options most suitable for the type of load.

Refer to the Programmes section to check the max load for each

programme.

Press the "On/Off " button.

Insert the plug into the socket.

Try to plug another appliance in the same socket. Do not use

connecting electrical devices to the socket, such as adapters or

extensions.

Wait for the power supply to be restored and switch the fuse on again

if necessary.

Close the door.

For machines equipped with this function: wait for the set delay to

end or switch the machine off to reset it. Refer to the Options section.

Press the "Start/Pause" button.

If Key Lock was selected, disable it. Switching the machine off will not

disable this option. Refer to the Options section.

The automatic programme has not sensed the required fi nal moisture

so that the dryer completes the programme and stops. If this happens

simply select an additional short period of drying or select Extra Dry

option if available.

Dryness levels can be modifi ed to the specifi c dryness desired.

Extra Dry is recommended for ready to wear items.

The drying cycle has to be set up once more and restarted.

Empty the water tank. Refer to the Cleaning & Maintenance section.

Clean the door fi lter and check whether air intake is free. Carrying out

these operations improperly may cause damages. Refer to Cleaning &

Maintenance section.

Clean the bottom fi lter. Refer to Cleaning & Maintenance section.

Switch the dryer off and unplug it. Open the door immediately and

pull laundry out, to allow the heat to dissipate. Wait for about 15

minutes. Reconnect the dryer to the power supply, load the laundry

and restart the drying cycle. If the problem still occurs, contact

the After-Sales Service Centre and communicate the letters and

digits fl ashing on the display.

For instance: F3 and E2.