Whirlpool 869991641560 빠른 시작 매뉴얼

{카테고리_이름} Whirlpool 869991641560에 대한 빠른 시작 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Whirlpool 869991641560 4 페이지.

페이지 인쇄

Quick guide

THANK YOU FOR BUYING A WHIRLPOOL PRODUCT.

In order to receive a more complete assistance, please

CONTROL PANEL

ON/OFF button (hold for Reset)

Programme selection Knob

Start/Pause

Options buttons*

Dryness level

Start delay

Timed drying

Cycle end

Rapid (hold for Key lock)

FreshCare+ (hold for Mute)

INDICATORS

Dryness level:

Iron dry -

Cycle phase:

Drying -

Empty water tank -

Refer to troubleshooting section:

FIRST TIME USE

Make sure that the water tank is correctly inserted. Make sure

that the drain hose on the back of the dryer is fixed correctly,

either to the dryer's water tank, or to your domestic drainage

system.

DAILY USE

Doing this will keep your machine working at its BEST:

- remember to empty your water tank after each drying cycle.

- remember to clean your filters after each drying cycle.

Refer to the Care & Maintenance section.

1. Plug the dryer into the power supply socket.

2. Open the door and load garments; always refer to instructions on

clothing labels and the max loads indicated in the programme

section. Empty pockets. Make sure garments do not get caught

between the door and/or the door filter. Do not load items that

are dripping wet. Do not tumble dry large, very bulky items.

3. Close the door.

4. Press the "On/Off" button.

5. Select the most suitable programme for the type of fabric in that

load.

6. Select the options, if necessary.

7. Press the "Start/Pause" button to begin drying.

8. At the end of the drying cycle, a buzzer will beep. An indicator on

the control panel signals the end of the cycle. Pull the load out

immediately to prevent the formation of creases on laundry.

9. Turn the machine off by pressing the "On/Off" button, open the

door and pull the clothing out. If the machine is not switched off

manually, after about a quarter of an hour from the end of the

cycle , the appliance turns off automatically to save energy.

Note that some programme/option accords with "Crease Care"

system. This means that for some hours, after the end of the

Policies, standard documentation, ordering of spare parts and additional product information can be

drying cycle, the drum rotates at regular intervals to prevent the

found by:

formation of creases.

• Visiting our website docs.whirlpool.eu and parts-selfservice.whirlpool.com

In case of power failure, it is necessary to press the "Start/Pause"

• Using QR Code

button to restart the cycle.

• Alternatively, contact our After-sales Service (See phone number in the warranty booklet). When

contacting our After-sales Service, please state the codes provided on your product's identifi cation plate.

Hanger dry -

Cupboard dry -

Cool down -

End of cycle.

Clean door filter -

Clean bottom filter -

Failure: Call after sales service

Before using the appliance carefully read the Safety

Instructions.

*Note: some models may have the wording in full instead of the icons.

Extra dry

Demo mode

DEMO

OPENING OF THE DOOR DURING THE CYCLE

Laundry can be checked while the drying cycle runs and any

garments already dry can be removed, while drying continues for

the remaining items. After closing the door, press the "Start/Pause"

button to resume machine operation.

Keep the door closed until the cycle end to save time and energy.

CARE LABEL

Always check the care labels, especially when placing garments in

the tumble dryer for the fi rst time. Below are the most commonly

used symbols:

May be tumble dried.

Do not tumble dry.

Tumble dry – high heat.

Tumble dry – low heat.

3''

xxxx

xxxxxxxxxxxx