Whirlpool 8TWED5620HW 사용 및 관리 매뉴얼 - 페이지 18

{카테고리_이름} Whirlpool 8TWED5620HW에 대한 사용 및 관리 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Whirlpool 8TWED5620HW 19 페이지. Electronic/electric & gas dryer
Whirlpool 8TWED5620HW에 대해서도 마찬가지입니다: 사용 및 관리 매뉴얼 (36 페이지)

페이지 인쇄

TROUBLESHOOTING

First try the solutions suggested here or visit our website at

If you experience

Dryer Results (cont.)

Odors (cont.)

Load too hot

Dryer Displaying Code Message or Indicator Is Lit

"PF" (power failure)

"L2" Diagnostic Code

(low or no line voltage

condition)

"F# E#" (F1 E1, F3 E1,

etc.) variable service

codes.

Check Vent indicator is lit The lint screen or vent is clogged;

"Loc"

for assistance and to possibly avoid a service call.

Possible Causes

Steam models only: For steam

cycles, the water is not properly

connected with the dryer.

Odors are left in garments after

wearing.

Load removed before cooldown

portion of cycle complete.

Using Timed Dry cycle with a high

temperature setting.

The drying cycle has been interrupted

by a power failure.

There may be a problem with your

home power supply, keeping the

dryer's heater from turning on.

The dryer is in need of service.

the vent is crushed or kinked or has

too many turns.

The Control Lock is enabled.

www.whirlpool.com/owners

Make sure water is connected to the dryer. Check that water

inlet hose is connected to both the faucet and dryer's water inlet

valve. Check that the water supply is turned on.

To remove odors left in garments after wearing, select Steam

Refresh. This cycle is best for reducing wrinkles and odors from

dry loads consisting of wrinkle-free cotton, cotton-polyester

blends, common knits, and synthetics.

Allow the dryer to complete the cooldown portion of the cycle

before removing the load.

Select an Automatic Cycle with a lower heat setting to avoid

overdrying the load.

Touch POWER to clear the display.

The dryer will continue to run when this diagnostic code is

present. Touch any pad to clear the code from the display and

return to the estimated time remaining.

NOTE: This error will only show during the initial installation.

Try the following:

•

Check to see if a household fuse has blown or circuit breaker

has tripped. Electric dryers use two household fuses or

breakers. Replace the fuse or reset the circuit breaker.

•

Confirm that the power cord is properly installed. Refer to

the Installation Instructions for details.

•

Select a Timed Dry heated cycle, and restart the dryer.

If the message persists, consult a qualified electrician.

If a code beginning with an "F" appears in the display, alternating

between F# and E#, the dryer control has detected a problem

that requires service. Call for service.

The dryer will continue to run when this indicator is lit. Try the

following:

• Clean lint screen.

• Check to see if the vent run from the dryer to the wall is

crushed or kinked.

• Confirm that the vent run from the dryer to the wall is free of

lint and debris.

• Confirm that the exterior vent exhaust hood is free of lint and

debris.

• Confirm that your vent system falls within the recommended

run length and number of elbows for the type of vent you

are using. Refer to "Plan Vent System" in the Installation

Instructions for details.

• Select a Timed Dry heated cycle, and restart the dryer.

• If the indicator remains lit, have your entire home venting

run cleaned.

Touch and hold CONTROL LOCK or DAMP DRY SIGNAL

(depending on the model) for 3 seconds to unlock the controls

of the dryer. During this time, the LED Display will count down

"3-2-1." When the Control Lock is disabled, the LED Display

will clear.

Solution