Whirlpool Cabrio WGD6600WL0 사용 및 관리 매뉴얼 - 페이지 18

{카테고리_이름} Whirlpool Cabrio WGD6600WL0에 대한 사용 및 관리 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Whirlpool Cabrio WGD6600WL0 48 페이지. Steam fabric care system gas dryer

페이지 인쇄

..................................................

The Damp Dry Signal is useful when drying bedsheets/linens

in a

Type of Load

Time*

(Minutes)

mixed load. When the signal goes off, open the door to stop the

.................................................

dryer, rearrange the load inside the dryer, close the door and

Olefin, polypropylene,

sheer nylon

10 - 20

restart the dryer to finish the drying cycle. Rearranging the load

will aid in the drying process.

*Reset cycle to complete drying, if needed.

When using Air Only

•

Check that coverings are securely stitched.

•

Shake and fluff pillows by hand periodically during the cycle.

•

Dry item completely.

Foam rubber pillows are slow to dry.

NOTE: Air Only is not available with Automatic

Cycles.

You can customize your cycles by selecting options.

NOTE: The Damp Dry Signal is available only with the Automatic

Cycles.

End of Cycle Signal

The End of Cycle Signal produces an audible sound when the

drying cycle is finished. Promptly removing clothes at the end of

the cycle reduces wrinkling.

Press END OF CYCLE SIGNAL until the desired volume (Loud,

Soft or Off) is selected.

DRUM LIGHT

WRINKLE S HIELD

DAMPDRY

SIGNAL

((nil)

ENDOFCYCLE

SIGNAL

NOTE: When the WRINKLE SHIELD

setting is selected and the

End of Cycle Signal is on, a tone sounds every 5 minutes until the

clothes are removed, or the WRINKLE SHIELD

setting ends.

OPTION;

Drum Light

On some models, select Drum Light to turn on the light inside the

dryer drum. During a cycle, if Drum Light is selected, the drum

light turns on and will remain on until DRUM LIGHT is pressed

again, the door is opened and closed, or the door is left open for

5 minutes.

When the dryer is not running, the drum light will turn on when

DRUM LIGHT is pressed or the dryer door is opened, and it will

remain on until the dryer door has been open for 5 minutes, the

dryer door is closed or DRUM LIGHT is pressed again.

Press DRUM LIGHT at any time to turn the drum light ON or OFE

WRINKLE

SHIELD

Setting

The WRINKLE SHIELD

setting helps keep wrinkles from

forming when you cannot unload the dryer promptly at the end of

a cycle. During this option, the dryer stops tumbling and then

tumbles again for a brief period.

•

Press the WRINKLE SHIELD

setting to get up to

120 minutes of heat-free, periodic tumbling at the end of a

cycle.

•

Stop the WRINKLE SHIELD

setting at any time by pressing

WRINKLE SHIELD

setting or opening the dryer door.

For the Perm Press/Casual Cycle, the WRINKLE SHIELD

setting is preset to ON. The other Automatic Cycles will retain

the WRINKLE SHIELD

setting. For example, if you select

the WRINKLE SHIELD

setting in the Normal cycle, the

WRINKLE SHIELD

setting will be on the next time you

select the Normal cycle.

NOTE: If you do not select the WRINKLE SHIELD

setting, the

dryer stops after cool down.

Damp Dry Signal

Select the Damp Dry Signal to alert you that your clothes are

approximately

80% dry. This is useful when you want to remove

lightweight items in a mixed load to avoid overdrying or remove

partially dry items that may need ironing.

You can change Automatic

and Timed Cycles, Modifiers and

Options anytime before pressing Start.

•

Three short tones sound if an unavailable combination

selected. The last selection will not be accepted.

Changing

Cycles after pressing Start

1. Press PAUSE/CANCEL twice.

2. Select the desired cycle and options.

3. Press START. The dryer starts at the beginning of the new

cycle.

NOTE: If you do not press Start within 5 minutes of selecting the

cycle, the dryer automatically

shuts off.

Changing

Modifiers

and Options

after pressing

Start

You can change an Option or Modifier anytime before the

selected Option or Modifier begins.

1. Press PAUSE/CANCEL once.

2. Select the new Option and/or Modifiers.

3. Press START to continue the cycle.

NOTE: If you happen to press PAUSE/CANCEL twice, the

program clears and your dryer shuts down. Restart the selection

process.

Changing

the Preset Dryness Level Settings

If all of your loads on all Auto Dry cycles are consistently not as

dry as you would like, you may change the preset Dryness Level

settings to increase the dryness. This change will affect all of your

Auto Dry cycles.

Your Dryness Level settings can be adjusted to adapt to different

installations, environmental

conditions or personal preference.

There are 3 drying settings: 1 (factory preset dryness level),

2 (slightly dryer clothes, approximately

15% more drying time)

and 3 (much dryer clothes, approximately

30% more drying

time).

1. The Dryness Level settings cannot be changed while the

dryer is running.