Whirlpool Cabrio,- WED7300X 사용 및 관리 매뉴얼 - 페이지 18

{카테고리_이름} Whirlpool Cabrio,- WED7300X에 대한 사용 및 관리 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Whirlpool Cabrio,- WED7300X 40 페이지. Top-loading high efficiency low-water washer
Whirlpool Cabrio,- WED7300X에 대해서도 마찬가지입니다: 사용 및 관리 매뉴얼 (40 페이지), 사용 및 관리 매뉴얼 (40 페이지), 사용 및 관리 매뉴얼 (36 페이지), 사용 및 관리 매뉴얼 (32 페이지), 설치 매뉴얼 (16 페이지), 사용 및 관리 매뉴얼 (40 페이지), 치수 및 설치 정보 (1 페이지), 치수 매뉴얼 (2 페이지), 사용 및 관리 매뉴얼 (40 페이지), 사용 및 관리 매뉴얼 (48 페이지), 사용 및 관리 매뉴얼 (40 페이지), 사용 및 관리 매뉴얼 (40 페이지), 사용 및 관리 매뉴얼 (40 페이지), 사용 및 관리 매뉴얼 (44 페이지), 사용 및 관리 매뉴얼 (19 페이지), Gude 사용 및 관리 (44 페이지), 사용 및 관리 매뉴얼 (44 페이지)

페이지 인쇄
Whirlpool Cabrio,- WED7300X 사용 및 관리 매뉴얼
TROUBLESHOOTING
First try the solutions suggested here or visit our website at www.whirlpool.com/help
If you experience
Error Code Appears in Display
oL (overloaded)
appears in display
uL (unbalanced load)
Load not balanced. The washer is
appears in display
running a load-balance correction
routine.
LF (too long to fill)
Washer taking too long to fill.
appears in display
Drain extends more than
4.5" (114 mm) into standpipe.
Ld (too long to drain
Washer taking too long to drain
water ) appears in
water. Drain extends more than
display
4.5" (114 mm) into standpipe.
HC (Hot and Cold
hoses reversed)
appears in display
Sd (Excess suds)
appears in display
dL (Lid cannot lock)
appears in display
lid (Lid opened)
appears in display
dU (Lid cannot unlock)
appears in display
F## code (F-type
error code) appears
in display
18
for assistance and to possibly avoid a service call.
Possible Causes
Load too large.
Hot and cold inlet hoses have been
installed incorrectly.
Excessive suds in washer. Washer is
running a suds reduction routine.
An item in the load may be keeping
the lid from locking.
Washer lid left open.
Objects on washer lid keep it from
unlocking.
System error code.
If the washer is overloaded, it will drain any water and detergent
in the washer. Remove several items and add HE detergent
Close lid and press START/PAUSE.
Allow the machine to continue. If the dial is flashing and the
machine has stopped, redistribute the load, close the lid, and
press START/PAUSE.
Check plumbing for correct drain hose installation. Use drain
hose form and attach securely to drainpipe or tub. Do not tape
over drain opening. See "Installation Instructions".
Check plumbing for correct drain hose installation. Use drain
hose form and attach securely to drainpipe or tub. Do not tape
over drain opening.
Lower drain hose if the end is higher than 96" (2.4 m) above
the floor. Remove any clogs from drain hose. See "Installation
Instructions".
This code will appear at the end of the wash cycle to indicate
that cold water hose is connected to the hot water inlet and hot
water hose is connected to the cold water inlet.
Allow the machine to continue. Use only HE detergent.
Always measure detergent, and base detergent quantity on
load size. Follow detergent manufacturer's instructions. If the
dial is flashing, reselect your desired cycle using a cold wash
temperature, and press START/PAUSE. Do not add detergent.
Make sure that the washer is not overloaded, and make sure no
items are above the top of the stainless steel basket.
Close the lid to clear the display. If the lid is left open for more
than 10 minutes, the cycle will reset and water in the washer
will drain.
Remove objects, such as a basket of laundry, from the top of
the washer.
Press START/PAUSE once to clear the code. Then press
START/PAUSE again to restart washer. If code appears again,
call for service.
Solution