Whirlpool CEM2750JQ0 설치 매뉴얼 - 페이지 5

{카테고리_이름} Whirlpool CEM2750JQ0에 대한 설치 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Whirlpool CEM2750JQ0 14 페이지. Commercial gas/electric dryer

페이지 인쇄

Check that dryer is equipped

with the correct

burner for the

particular

type of gas used. Burner

information

can be found

on the

serial/rating

plate

In the door well of

the appliance.

If this information

does

not agree

with the type of gas

available,

see your dealer,

mThis dryer is equipped

for use

with NATURAL GAS. It is certified

CSA International

for manufactured,

mixed and L.P, (propane

and

butane)

gases with appropriate

conversion.

No attempt

shall be

made

to convert

the appliance

from

the gas specified

on the serial/rating

plate for use with a different

gas

without

consulting

the serving gas

supplier. Conversion must be done by

a qualified service

technician.

Gas

conversion kit port numbers are listed

on the gas valve burner base.

mProvide

a rigid gas supply line of

1/2-inch

IPS pipe to the dryer

location.

If the total length of the

supply line is more than

20 feet

(6.1 m), larger pLpe will be needed.

For L.P. gas usage, 3/8-Inch,

approved

copper

tubing

may be

used, Pipe-joint

compounds

suitable

for use with L.P. gas should

be use

FnThe

supply line shall be equipped

with a shutoff valve installed

within 6

ft. (1.8 m) of dryer in accordance

with

the National

Fuel Gas Code,

ANSI

Z223,1 -- latest edition*.

In Canada,

an individual

manual

shutoff valve

must be installed in accordance

with

the B 149 installation

codes

CAN/CGA

B149.1 and CAN/CGA

B149.2", This

valve should

be located

in the same

room as the dryer and should be in a

location

that aUows ease of opening

and closing.

Do Not block access to

the shutoff valve.

i If the dryer is Installed

in a

confined

area such as a bathroom

closet, provision

must be made

for

enough

air for combustion

and

ventilation.

(Check

governing

codes

and ordinances,

or refer to the

section

of this instruction

covering

recessed

and closet installations.)

m If local codes

and ordinances

permit,

it is recommended

that new

flexible metal

tubing,

design-certified

by the AGA or CSA, be used for

connecting

the dryer to the gas

supply line, (The gas feed

pipe which

extends

through

the lower rear of the

dryer is provided

with 3/8-inch

metal

pipe thread,)

Lf rigid

pipe is used

asa

I I

combination

of pipe fittings must

be used to obtain

an in-line

connection

to the dryer.

n Make sure that lower edges of

the cabinet,

plus the back and

bottom

sides of the dryer are free of

obstructions

to permit

adequate

clearance

of air openings

for

combustion

air, See "Recessed

area

and closet installation

instructions,"

page

12, for minimum

spacing

requirements,

For ease of installation,

operation

and servicing

(If ever

needed)

adequate

space

should

provided

around

the dryer,

A 1/8-inch

NPT plugged

tapping,

accessible

for gauge

testing,

must be

installed

immediately

upstream

of the

gas supply connection

to the dryer,

The dryer must be disconnected

from

the gas supply piping

system during

any pressure testing of the system at

test pressures in excess of 1/2 psig.

The dryer must be isolated from the gas

supply piping system by closing the

equipment

shut-off valve during any

pressure testing of the gas supply piping

system at test pressures equal to or less

than 1/2 psi (3,45 kPa)

EJectrlcal

requirements

Electrical Shock Hazard

Plug into a grounded 3-prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructlons

can result In death,tim, or electrlcal

shock.

A 120-volt, 60-Hz, AC-only,

15-or

20-ampere

fused electrical

supply is

required.

A time-delay

fuse or circuit

breaker

is recommended,

It is recommended

that a separate

circuit serving only this appliance

provided,

If codes permit and a separate ground

wire is used, it is recommended that a

qualified electrician determine that the

ground path Is adequate.

Recommended

ground method

The dryer, when installed,

must be

electrically

grounded

in accordance

with local codes,

or in the absence

local codes,

with the National

Electrical

Code,

ANSI/NFPA 70**, or

the Canadian

Electrical

Code,

CSA

C22.1".

GROUNDING

INSTRUCTIONS: This

appliance

must be grounded.

In the

event of malfunction

or breakdown,

grounding

will reduce

the risk of

electric

shock by providing

a path of

least resistance

for electric

current.

The power

supply cord plug must be

plugged

into an appropriate

outlet

that is properly

installed

and

grounded

in accordance

with all

local codes

and ordinances,

WARNING - Improper

connection

the equipment-grounding

conductor

can result in a risk of electric

shock.

Check with a qualified

electrician

serviceman

if you are in doubt

as to

whether

the appliance

is properly

grounded.

Do not modify

the plug

provided

with the appliance

- if it will

not fit the outlet,

have a proper

outlet

installed

by a qualified

electrician.

3-prong ground-type

outlet

3-pron_ _

grouna

_:_

.°°

power /

supply cord

ground

prong

Copies

of the standards

listed above

may

be obtaLned

from:

* CSA international

8501 East Pleasant

Valley Road

Cleveland,

Ohio 44131-5575

** National

Fire Protection

Association

One Batteryrnarch

Park

Quinoey,

Massachusetts

02269

Important: Observe all gaveming

codes and ordinances.

Page 5