Whirlpool CSP2761TQ4 설치 지침 매뉴얼 - 페이지 7

{카테고리_이름} Whirlpool CSP2761TQ4에 대한 설치 지침 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Whirlpool CSP2761TQ4 36 페이지. Commercial stacked dryer gas (120-volt,60-hz)or electric (120/240-volt,60-hz)

페이지 인쇄

0s iiiiiii ¸'}

iMPORTANT: The dryer must be electrically grounded m

accordance with local codes and ordinances or, in the absence

of local codes, with the National Electrical Code, ANSI/NFPA 70,

latest edition.

The National Electrical Code requires a 4-wire supply connection

for homes built after 1996, dryer circuits involved in remodeling

after 1996, and all mobile home installations.

If codes permit and a separate ground wire is used, it is

recommended

that a qualified electrical installer determine

that the ground path is adequate.

A copy of the above code standards can be obtained from:

National Fire Protection Association

One Batterymarch Park, Quincy, MA 02269

[]

A four-wire or three-wire, single-phase,

120/240 volt,

60 Hz, AC only electrical supply (or four-wire or three-wire,

120/208 volt, if specified on the model/serial rating plate) is

required on a separate, 30-amp circuit, fused on both sides of

the line. A time-delay fuse or circuit breaker is recommended.

Recommended

Ground

Method

It is your responsibility to contact a qualified electrical installer

to ensure that the electrical installation is adequate and in

conformity with the National Electrical Code, ANSl/NFPA 70,

latest edition, and all local codes and ordinances.

GROUNDING

INSTRUCTIONS

[] For a grounded, cord-connected

dryer:

This dryer must be grounded. In the event of a malfunction or

breakdown, grounding will reduce the risk of electric shock

by providing a path of least resistance for electric current.

This dryer uses a cord having an equipment-grounding

conductor and a grounding plug. The plug must be plugged

into an appropriate outlet that is properly installed and

grounded in accordance with all local codes and ordinances.

[] For a permanently

connected dryer:

This dryer must be connected to a grounded metal,

permanent wiring system, or an equipment-grounding

conductor must be run with the circuit conductors and

connected to the equipment-grounding

terminal or lead on

the dryer.

WARNING:

improper connection of the equipment-

grounding conductor can result in a risk of electric shock.

Check with a qualified electrician or service representative or

personnel if you are in doubt as to whether the dryer is

properly grounded. Do not modify the plug on the power

supply cord: if it will not fit the outlet, have a proper outlet

installed by a qualified electrician.

SAVE THESE

INSTRUCTIONS

Explosion

Hazard

Use a new CSA International

approved

gas supply line.

Instafl a shut=off valve.

Securely

tighten

all gas connections.

if connected to LP, have a qualified

person make sure

gas pressure does not exceed 13" (330 ram) water

coJumn.

Examples of a qualified

person include:

licensed heating personnel,

authorized

gas company personnel, and

authorized

service personnel.

FaiJure to do so can result in death, explosion,

or fire.

iMPORTANT: Observe all governing codes and ordinances.

This installation must conform with all local codes and

ordinances. In the absence of local codes, installation must

conform with American National Standard, National Fuel Gas

Code ANSI Z223.1/NFPA 54.

A copy of the above code standards can be obtained from:

National Fire Protection Association

One Batterymarch Park, Quincy, MA 02269

The design of this dryer has been certified by CSA international

for use at altitudes up to 10,000 feet (3048 m) above sea level at

the B.T.U. rating indicated on the model/serial plate. Burner input

adjustments are not required when the dryer is operated up to

this elevation.

When installed above 10,000 feet (3048 m), a four percent (4%)

reduction of the burner B.T.U. rating shown on the model/serial

plate is required for each 1,000 foot (305 m) increase in elevation.

For assistance when converting to other gas types and/or

installing above 10,000 feet (3048 m) elevation, contact your

local service company.

Type of Gas

This dryer is equipped for use with natural gas. It is design-

certified by CSA international for L.R (propane and butane) gases

with appropriate conversion. No attempt shall be made to convert

the dryer from the gas specified on the serial/rating plate for use

with a different gas without consulting the serving gas supplier.

Conversion must be done by a qualified service technician.

Gas conversion kit part numbers are listed on the gas valve

burner base.