Whirlpool Duet GGW9200LL1 사용 및 관리 매뉴얼 - 페이지 21

{카테고리_이름} Whirlpool Duet GGW9200LL1에 대한 사용 및 관리 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Whirlpool Duet GGW9200LL1 48 페이지. Electronic gas dryer

페이지 인쇄

Moving care

•

1. Unplug the power supply cord.

2. Close shutoff valve in gas supply line.

Disconnectgassupplylinepipeandremovefittingsattached

to dryer pipe.

•

4. Cap the open fuel supply line.

Make sure leveling legs are secure in dryer base.

Use masking tape to secure dryer door.

The dryer light automatically turns on inside the dryer drum when

you open the door.

To change the drum light

1. Unplug dryer or disconnect

power.

2. Open the dryer door. Locate the light bulb cover on the back

wall of the dryer. Remove the screw located in the lower right

corner of the cover. Remove the cover.

3. Turn bulb counterclockwise.

Replace the bulb with a lO-watt

appliance

bulb only. Replace

the cover and secure

with the

screw.

Plug in dryer or reconnect power.

TROUBLESHOOTING

First try the solutions suggested here and possibly avoid

the cost of a service call...

Dryer displaying

code message

•

"PF" (power failure), check the following:

Was the drying cycle interrupted by a power failure?

Press (and hold) HOLD TO START button to restart the dryer.

Is the dryer located in a room with temperature

below

45°F (7°C)?

Proper operation of dryer cycles requires temperatures above

45°F (7°C).

Was a cold rinse water used? Was the load very wet?

Expect longer drying times with items rinsed in cold water

and with items that hold moisture (cottons).

Is the load too large and heavy to dry quickly?

Separate the load to tumble freely.

Dryer will not run

•

Check the following:

Is the power cord plugged in?

Has a fuse blown, or has circuit breaker tripped?

Was a regular fuse used? Use a time-delay fuse,

Is the dryer door firmly closed?

Was HOLD TO START firmly pressed and held for at least 1

second?

Is a cycle selected?

Unusual sounds

•

Has the dryer had a period of non-use?

If the dryer hasn't been used for a while, there may be a

thumping sound during the first few minutes of operation.

The gas valve clicking is a normal operating sound.

Lint on load

•

Is the lint screen clogged?

Clean lint screen. Check for air movement.

•

"E" Variable (El, E2, E3) service codes:

Call for service.

Clothes

are not drying satisfactorily

•

Checkthe

following:

Is the lint screen clogged with lint?

Is the exhaust vent or outside exhaust hood clogged with lint,

restricting air movement? Run the dryer for

5-10 minutes. Hold your hand under the outside exhaust

hood to check air movement. If you do not feel air movement,

clean exhaust system of lint or replace exhaust vent with

heavy metal or flexible metal vent (see "Installation

Instructions").

Is the exhaust vent crushed or kinked? Replace with a heavy

metal vent (see "Installation

Instructions").

Has a fuse blown, or a circuit breaker tripped?

Has an air cycle been selected? Select the right cycle for the

types of garments being dried (see "Cycles").

Is the automatic cycle ending early? The load may not be

contacting

the electronic sensor strips, level the dryer.

Is the valve open on the gas supply line?

Are fabric softener sheets blocking the grille? Use only one

fabric softener sheet and only use it once.

Is load properly sorted?

Sort lint givers (towels, chenille) from lint takers (corduroy,

synthetics). Also sort by color.

Is the load too big or too heavy?

Dry smaller loads so lint can be carried to the lint screen.

Was the load overdried?

Use correct dryer settings for load type (see "Cycles").

Overdrying can cause lint-attracting

static electricity.

•

Was paper or tissue left in pockets?

Is pilling being mistaken

for lint?

Pilling (surface fuzz) is caused by normal wear and

laundering.

Stains on load or color change

•

Was dryer fabric softener properly used?

Add dryer fabric softener sheets at the beginning of the cycle

when the load is cold. Do not add fabric softener sheets to a

warm load.

•

Were items soiled when placed in the dryer?

Items should be clean before being dried.

•

Were items properly sorted?

Sort light colors from dark colors. Sort colorfast items from

noncolorfast

items.