Whirlpool Duet GGW9250PW3 사용 및 관리 매뉴얼 - 페이지 13
{카테고리_이름} Whirlpool Duet GGW9250PW3에 대한 사용 및 관리 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Whirlpool Duet GGW9250PW3 44 페이지. Electronic gas dryer
페이지 인쇄
DRYER USE
Status
Control On
O Se,sing
0
Heavy Duty_
0 Wet
Normal_
0 Da_,,p
_
OMoro
Bulky.d_,/
o.oo., .... \ o
I,e,,,, IF41
OW, lnkleShi_/d \0
Delicate*k_
Dryness
0 ControlLocked
\
Level
"_
C----qE,,im ,od
/I
"ll'r,_dDry
...'-_ I
P ....
/
0_/
Less[
"l l
Cancel
_/.Touc_ Up
T'me k.J/ l/._ _
"_,.'. Q,ic_ Dry
I \j
0
H_gh
0
Medium
0 Low
0
Louder
0
Extra Low
0 Softer
0
On
0
Air Only
0
Off
0
0
0
Wrinkle Shield
Temperature
End Of Cycle Signal
(Manuel
Cyc}esvrdy)
Hold for3 Seconds _o
iock / Uplock C_nttol
J
Explosion
Hazard
Keep flammable
materials
and vapors,
such as
gasoline,
away from dryer.
Do not dry anything
that has ever had anything
flammable
on it (even after washing).
Failure to follow
these instructions can result in death,
explosion,
or fire.
3. Rotate the dial to select either an Automatic or Manual Cycle
then press the CONTROL ON button, The preset settings and
drying time for the cycle chosen will be displayed.
To use an Automatic Cycle
Point the dial to an Automatic Cycle.
Select DRYNESS LEVEL to adjust how dry you want the
load to be. The time displayed is an estimated length of
the cycle based on the Dryness Level selected, As the
cycle runs, the control senses the dryness of the load and
adjusts the time automatically for the selected Dryness
Level.
0 More
0
O Lees
Fire Hazard
No washer can completely
remove oil.
Do not dry anything
that has ever had any type of oil on
it (including
cooking
oils).
items containing
foam, rubber,
or plastic must be dried
on a clothesline
or by using an Air Cycle.
Failure to follow
these instructions can result in death
or fire.
The following is a guide to starting your dryer. Please refer to
specific sections of this manual for more detailed information.
1. Clean lint screen before or after each cycle. See "Cleaning
the Lint Screen."
2. Place laundry into dryer and shut door. See "Loading."
©
Dryness
Level
NOTE: Time is not adjustable for Automatic
Cycles. Pressing
the More Time or Less Time buttons will cause a triple beep,
indicating that the time cannot be changed.
•
Press the WRINKLE SHIELD
TM
feature button if this
option is desired.
•
Press the END OF CYCLE SIGNAL button to set signal
volume to desired level.
•
Press (and hold) HOLD TO START button until dryer starts
(about 1 second).
Once an Automatic
cycle has started, the WRINKLE
SHIELD
TM
feature and the End of Cycle Signal level can be
adjusted. Press the PAUSE/CANCEL key twice to stop the
dryer and clear the settings, allowing you to select another
cycle and Dryness Level.
13