Whirlpool Gold GGQ8811PW2 설치 지침 매뉴얼 - 페이지 7
{카테고리_이름} Whirlpool Gold GGQ8811PW2에 대한 설치 지침 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Whirlpool Gold GGQ8811PW2 28 페이지. 27"(69cm) gas dryer
Whirlpool Gold GGQ8811PW2에 대해서도 마찬가지입니다: 사용자 지침 (17 페이지)
페이지 인쇄
Alternate
installations for close clearances
Venting systems come in many varieties. Select the type best for
your installation, Two close-clearance
installations are shown.
Refer to the manufacturer's instructions.
A. Over-The-Top installation
(also available
with one offset elbow)
B. Periscope installation
NOTE: The following kits for close clearance alternate installations
are available for purchase. Please reference the "Assistance
or
Service" section of the "Dryer User Instructions."
•
Over-The-Top Installation:
Part Number 4396028
Periscope Installation (For use with dryer vent to wall vent
mismatch):
Part Number 4396037 - 0" (0 cm) to 18" (45.72 cm) mismatch
Part Number 4396011 - 18" (45.72 cm) to 29" (73,66 cm)
mismatch
Part Number 4396014 - 29" (73.66 cm)to 50" (127 cm)
mismatch
Special provisions for mobile home installations
The exhaust vent must be securely fastened to a noncombustible
portion of the mobile home structure and must not terminate
beneath the mobile home. Terminate the exhaust vent outside,
/1
Determine
vent length
1. Select the route that will provide the straightest and most
direct path outdoors. Plan the installation to use the fewest
number of elbows and turns, When using elbows or making
turns, allow as much room as possible, Bend vent gradually to
avoid kinking. Avoid 90 ° turns when possible.
2,
Determine vent length.
The maximum length of the exhaust system depends upon:
•
The type of vent (rigid metal or flexible metal).
•
The number of elbows used.
•
Type of hood.
Recommended
hood styles are shown here.
B
(10.2crn)
A. Louvered hood style
B. Box hood style
The angled hood style (shown following) is acceptable.
(6.4 cm)
See the exhaust vent length chart that matches your hood
type for the maximum vent lengths you can use,
Exhaust systems longer than specified will:
•
Shorten the life of the dryer.
•
Reduce performance,
resulting in longer drying times and
increased energy usage,
3. Determine the number of elbows you will need,
NOTE: Do not use vent runs longer than specified in the Vent
Length Chart,
The following chart helps you determine your maximum vent
length based on the number of 90 ° turns or elbows you will
need and the type of vent (rigid or flexible metal) and hood
that you will use,
Vent Length Chart
Number of
Type of vent
Box or
Angled
90 ° turns
Iouvered
hoods
or elbows
hoods
0
Rigid metal
64 ft (20 m)
58 ft (17.7 m)
Flexible metal
36 ft (11 m)
28 ft (8.5 m)
1
Rigid metal
54 ft (16.5 m)
48 ft (14.6 m)
Flexible metal
31 ft (9.4 m)
23 ft (7 m)
2
Rigid metal
44 ft (13.4 m)
38 ft (11.6 m)
Flexible metal
27 ft (8.2 m)
19 ft (5.8 m)
3
Rigid metal
35 ft (10.7 m)
29 ft (8.8 m)
Flexible metal
25 ft (7.6 m)
17 ft (5.2 m)
4
Rigid metal
27 ft (8.2 m)
21 ft (6.4 m)
Flexible metal
23 ft (7 m)
15 ft (4.6 m)
NOTE: Side and bottom exhaust installations have a 90 ° turn
inside the dryer. To determine maximum exhaust length, add one
90 ° turn to the chart.