Whirlpool WGD9470WW 사용 및 관리 매뉴얼 - 페이지 9

{카테고리_이름} Whirlpool WGD9470WW에 대한 사용 및 관리 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Whirlpool WGD9470WW 28 페이지. Duet steam and non-steam electronic gas dryer
Whirlpool WGD9470WW에 대해서도 마찬가지입니다: 설치 지침 매뉴얼 (32 페이지), 사용 설명서 (8 페이지), 제품 치수 (1 페이지)

페이지 인쇄

Damp Dry Signal

On some models, the Damp Dry Signal may be selected to alert

you that your clothes are approximately 80% dry. This is useful

when you want to remove lightweight items in a mixed load to

avoid overdrying or remove partially dry items that may need

ironing.

The DAMP DRY SIGNAL is useful when drying bedsheets/linens in

a mixed load. When the signal goes off, open the door to stop the

dryer, rearrange the load inside the dryer, close the door and

restart the dryer to finish the drying cycle. Rearranging the load

will aid in the drying process.

NOTE: The Damp Dry Signal is available only with the Automatic

Cycles. The Damp Dry Signal is not a selectable option for the

Sanitize cycle.

Cycle Signal

The End of Cycle Signal produces an audible sound when the

drying cycle is finished.

Press until the desired volume (Loud, Soft, or Off) glows green.

NOTE: When the WRINKLE SHIELD™ feature is selected and the

End of Cycle Signal is on, an audible sound will be emitted every

5 minutes until the clothes are removed, or the WRINKLE

SHIELD™ feature is finished.

Button Sound

You can change the volume of the sound of the beeps. Press until

the desired volume (Loud, Soft, or Off) glows green. The Power

and Cancel buttons will still beep softly even when the Button

Sound volume is set to Off.

Control Lock/Unlock

This feature allows you to lock your settings to avoid unintended

use of the dryer. You can also use the Control Lock feature to

avoid unintended cycle or option changes during dryer operation.

To enable the Control Lock feature when dryer is running:

Press and hold the CONTROL LOCK/UNLOCK button for

3 seconds. The control is locked when a double beep is heard and

the Control Lock status light is on.

■

When the dryer is off, it is not necessary to press the Control

On button before activating the Control Lock feature.

To unlock:

Press and hold the CONTROL LOCK/UNLOCK button for

3 seconds to turn this feature off.

NOTE: When the dryer is running and Control Lock is on, the

dryer can be stopped by pressing the Pause/Cancel button, but

cannot be restarted until the control is unlocked.

Changing Cycles, Options, and Modifiers

You can change Auto Cycles, Timed Cycles, Options, and

Modifier, and anytime before pressing Start.

■

Three short tones sound if an unavailable combination is

selected. The last selection will not be accepted.

Changing Cycles after pressing Start

1. Press PAUSE/CANCEL twice. This ends the current cycle.

2. Select the desired cycle and options.

3. Press and hold START. The dryer starts at the beginning of the

new cycle.

NOTE: If you do not press Start within 5 minutes of selecting the

cycle, the dryer automatically shuts off.

Changing Options and Modifiers after pressing Start

You can change an Option or Modifier anytime before the selected

Option or Modifier begins.

1. Press PAUSE/CANCEL once.

2. Select the new Option and/or Modifier.

3. Press and hold START to continue the cycle.

NOTE: If you happen to press Pause/Cancel twice, the program

clears and your dryer shuts down. Restart the selection process.

Changing the Preset Dryness Level Settings

If all your loads on all Auto Dry cycles are consistently not as dry

as you would like, you may change the preset Dryness Level

settings to increase the dryness. This change will affect all of your

Auto Dry cycles.

Your Dryness Level settings can be adjusted to adapt to different

installations, environmental conditions or personal preference.

There are 3 drying settings: 1 (factory preset dryness level),

2 (slightly drier clothes, approximately 15% more drying time),

and 3 (much drier clothes, approximately 30% more drying time).

1. The Dryness Level settings cannot be changed while the dryer

is running.

2. Press and hold the Dryness Level button for 5 seconds. The

dryer will beep, and "CF" will be displayed for 1 second

followed by the current drying setting.

3. To select a new drying setting, press the Dryness Level key

again until the desired drying setting is shown.

NOTE: While cycling through the settings, the current setting

will not flash, but the other settings will flash.

4. Press START to save the drying setting.

5. The drying setting you selected will become your new preset

drying setting for all Auto Dry cycles.