Whirlpool WGD96HEAW 사용 설명서 - 페이지 6

{카테고리_이름} Whirlpool WGD96HEAW에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Whirlpool WGD96HEAW 8 페이지. 7.4 cu. ft. duet steam gas dryer with advanced moisture sensing
Whirlpool WGD96HEAW에 대해서도 마찬가지입니다: 사용 및 관리 매뉴얼 (40 페이지), 설치 지침 매뉴얼 (44 페이지)

페이지 인쇄

■

For closet installation, with a door, minimum ventilation

openings near the top and bottom of the door are required.

Louvered doors with equivalent ventilation openings are

acceptable.

■

Companion appliance spacing should also be considered.

Recommended room venting and installation spacing for

recessed or closet installation, with stacked washer

and dryer

48 in.

(310 cm

)

24 in.

(155 cm

)

*Recommended spacing.

"AF" Code

Certain electronic dryer models have airflow detection

capabilities. (See specific model product literature for details). If

the airflow in the dryer is extremely low, an "AF" code will be

displayed on the control panel. For single dryer venting systems,

this code means that you may have a blocked or partially blocked

vent or that your overall vent system length is too long. To resolve

this issue:

■

Check to see if the vent run from the dryer to the wall is

crushed. Refer to the "Venting Requirements" section of

the Use and Care Guide for more information.

■

Confirm that the vent run from the dryer to the wall is free

of lint and debris.

■

Confirm that the exterior vent exhaust hood is free of lint

and debris.

■

Confirm that your vent system falls within the

recommended run length and number of elbows

for the type of vent you are using. Refer to the "Plan

Vent System" section of the Use and Care Guide for

details.

■

Select a Timed Dry heated cycle, and restart the dryer.

■

If the message persists, have your entire home venting run

cleaned.

For multi-dryer venting systems, the "AF" code means that your

vent may be blocked or partially blocked or that the venting

system is creating back pressure in excess of the maximum

allowed. In this case, the engineering firm that designed the

system should be consulted.

3"* (76 mm)

1"* (25 mm)

Multiple Dryer Venting Systems

Multiple dryer venting systems must be designed specifically for

each application.

NOTE: It is recommended that an architectural or HVAC

engineering firm be consulted for designing the dryer venting

system.

Connecting a number of dryers to a single vent system is

common in coin-laundry stores and in many apartment

buildings. Listed here are some requirements for examples

of three different multiple dryer venting systems.

Option 1 - Horizontal System

The most common is the horizontal system, in which banks of

dryers are all located in one room and vented through a common

duct. See the following illustration for an example of a generic

horizontal system.

A. 4" (102 mm) diameter rigid metal back draft damper

*Minimum spacing required between dryers

Option 2 - Vertical System

The vertical system is used in some apartment buildings that have

a washer and dryer on each floor. Each dryer is exhausted into the

same central vertical duct. See the following illustration for an

example of a generic vertical system.

A. Maximum back pressure measurement location

B. Weighted dampers

C. Individual dryer exhaust - on each floor

D. 0.1" (2.5 mm) water column maximum vacuum

E. Main duct

F. Barometric damper (use depends on exhaust

system design)

G. Source of outside air