Whirlpool YCEE2760KQ1 설치 지침 매뉴얼 - 페이지 3

{카테고리_이름} Whirlpool YCEE2760KQ1에 대한 설치 지침 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Whirlpool YCEE2760KQ1 27 페이지. Commercial dryer gas or electric

페이지 인쇄

The console

houses the electronic

control

board,

The board

is factory

set for a dry time of 45 minutes,

Consult the tech sheet found inside

the dryer toe panel

to reset dry time

and for other options,

The coin-slide

mechanism,

control

panel

lock and key, and coin-box

lock and key are not included

and

are available

from usual industry

sources,

IMPORTANT SETUP INFORMATION

The electronic

control

is factory

preset to accept

commands

from a

Palm®handhold

equipped

with the

appropriate

Whirlpool

management

software,

If a handheld

is not to be

used, the handhold

functionality

MUST BE DISABLED as part of the

control

set up, Failure to disable

handhold

functionality

may result in

unauthorized

machine

access,

Exhaust

requirements

Fire Hazard

Use a heavy metal vent.

Do not use a plastic vent.

Do not use a metal foil vent.

Failure to do so can result in

death or fire,

Do not use non-metal

flexible vent,

metal vent that is smaller than four

inches in diameter

or exhaust hoods

with magnetic

latches,

The dryer must be exhausted

outdoors.

Do not exhaust dryer into a gas vent,

chimney,

wall, ceiling,

or concealed

space

of a building,

Do not install flexible vent in enclosed

walls, ceilings or floors,

If using an existing exhaust system,

clean

lint from entire length of exhaust

system, Make sure exhaust hood is not

plugged

with lint,

The exhaust system should be

inspected

and cleaned

yearly,

Replace

any plastic or metal foil

exhaust vent with rigid metal

or flexible

metal vent,

Use 4" (10,2 cm) vent clamps to

secure vent system,

exhaust airflow

beffer

[==] good

Four-inch (10.2 cm) metal exhaust vent

isrequired,

Plan installation to use the

fewest

number

of elbows and turns,

Metal flexible vent must be fully

extended

and supported

when the

dryer is in its final position,

DO NOT

KINK OR CRUSH THE VENT, The metal

flexible vent must be completely

open to allow adequate

exhaust air

to flow.

Allow as much

room as possible

when using elbows or making turns,

Bend vent gradually

to avoid kinking,

Remove

excess flexible vent to avoid

sagging

and kinking that may result in

reduced

air flow,

Exhaust outlet is located

at the

center

of the bottom

dryer back,

The exhaust vent can be routed up,

down,

left, right, behind

the dryer or

straight

out the back of the dryer,

Maximum

length of exhaust

system

depends

upon the type of vent used,

number

of elbows and type of

exhaust

hood, The maximum

length

for both rigid and flexible vent is

shown in the chart,

EXHAUSTHOOD TYPE

4 •

(10.2 cm)

10.2 cm)

turns

_ y

MAI_MUMLE_I_lltOF 4-1N_'t

RIGID METAL t _NT

10.2 _

DIAMEI_R

64 FT. 1 19.5ml

64 FT. (19.5ml

58 FT. 117.7 r_

54 FT. (16.5 m)

54 FT.116.5 m)

48 FT.(14_ n0

44 FT. (13.4 rn]

44 FT.(13.4 rn]

38 FT.(11_ n0

36 FT. (10.7 m)

36 FT.(I0.7 m)

29 FT.(8.8 m]

27 FT. (8.2 m)

27 FT.(8.2 m)

21 FT.(5.4 m)

MAXIMUM LEN@111 OF4-1NCH(I 0.2 cm) DIAMb'IIE R

FL_BLEMETAL VENT

36 FT.(11.0 m)

28 FT.(8_ m)

31 FT.(gA m)

31 FT.(9.4 m)

23 FT.(7_ m)

27 FT.(8.2 n0

27 FT.(8.2 m)

19 FT.(6Ji m]

25 FT.(7_ rn)

26 FT.(7.6 m]

17 FT.(6.2 m]

23 FT.(7.On0

23 FT.(7.0 m]

15 FT.(4_ m]

For exhaust systems not covered

the exhaust

length chart, see

Whirlpool

Service Manual,

"Exhausting

Whirlpool

Dryers," Part No, 603197,

available

from your Whirlpool

parts

distributor,

If dryer is installed in a confined area,

such as a bedroom,

bathroom or

closet, it must be exhausted

to the

outside and provision

made for

enough

air for combustion

and

ventilation,

(Check

governing

codes

and ordinances,)

See "Recessed

area

and closet installation

instructions"

Page 12,

Page 3