Whirlpool YWED9600TA1 사용 및 관리 매뉴얼 - 페이지 13

{카테고리_이름} Whirlpool YWED9600TA1에 대한 사용 및 관리 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Whirlpool YWED9600TA1 48 페이지. Electronic electric dryer

페이지 인쇄

1. Table of Contents

•

Press the DAMP DRY CYCLE SIGNAL button to set damp

dry signal volume to desired level.

•

Press and hold START button until dryer starts (about

1 second).

Once an Automatic

cycle has started, the WRINKLE

SHIELD

feature and cycle signals can be adjusted. Press

the PAUSE/CANCEL key twice to clear the settings, allowing

you to select another cycle and Dryness Level.

NOTE: Time and Temperature are not adjustable for

Automatic Cycles. Pressing the DRY TIME or TEMPERATURE

buttons will cause a triple beep, indicating that the time

cannot be changed.

How Automatic

Cycles Work

The AccelerCare

function improves drying performance

with Auto Moisture Sensing Plus, which advances the cycle

as moisture is extracted from clothing. A thermistor

(electronic temperature sensor) and moisture sensing strips in

the dryer drum help measure the amount of moisture in the

clothes as they tumble. An electronic control determines the

load type to help save time, avoid overdrying, and increase

the accuracy of the end dryness level. After the first 5 minutes

of an automatic cycle, the estimated time display will adjust

based on the approximate

load size, cycle, dryness level

selected and amount of moisture left in the clothes. When the

clothes have reached approximately

80% of the dryness level

selected, the estimated time display will adjust again,

showing the final drying time. The AccelerCare

feature

takes the guesswork out of drying time and enhances fabric

care.

To use a Manual Cycle

NOTE: A light next to each feature will glow green when the

feature is selected or will glow amber when the feature is

selectable. The light will not glow when the selection is

unavailable with the cycle or option combinations

selected.

•

Press POWER.

Rotate the dial to select a Manual Cycle.

Press the DRY TIME up or down buttons until the desired

drying time is displayed. Press DRY TIME, and the time

will change by 1-minute intervals. Press and hold DRY

TIME, and the time will change by 5-minute intervals. The

initial time displayed is the actual drying time.

Adiust M anual

Dry Tree

®®

The Dry Time feature can be used only with Manual

Cycles and the Enhanced Touch Up Cycle.

Press TEMPERATURE until the desired temperature

glows green.

High

Medium

Low

ExtraL0w

_' Air OnHy

•

Press the CYCLE SIGNAL button to set end of cycle

signal volume to desired level.

•

Press and hold START button until dryer starts (about

1 second).

NOTE: Dryness Level is not adjustable for Manual, Steam or

Sanitize Cycles. Pressing the Dryness Level button will cause

the triple beep indicating that this option is not selectable.

While a Manual Cycle is running, you cannot change the

cycle until you clear the settings. You can change the settings

for Time, Temperature, the WRINKLE SHIELD

feature and

the cycle signals. Press the PAUSE/CANCEL key twice to

clear the settings, allowing you to select another cycle.

To use a Steam Cycle

•

Press the POWER button.

Rotate the dial to select either the Enhanced Touch Up or

Quick Refresh cycles.

Press the DRY TIME up or down buttons until the desired

drying time is displayed. Press DRY TIME, and the time

will change by 1-minute intervals. Press and hold DRY

TIME, and the time will change by 5-minute intervals. The

initial time displayed is the actual drying time.

NOTE: The More Time and Less Time buttons can be

used only with Manual Cycles and the Enhanced Touch

Up Cycle.

Adjust Mal_ual

DlyTime

•

Press TEMPERATURE until the desired temperature

glows green.

NOTE: During the Enhanced Touch Up Cycle, you can

change the settings for Time, Temperature, the WRINKLE

SHIELD

feature and Cycle Signal. During the Quick Refresh

Cycle you can change the WRINKLE SHIELD

feature and

the Cycle Signal. Press STOP twice to stop the dryer and

clear the settings. Select another cycle or option.

To stop your dryer at any time

Press PAUSE/CANCELtwice or open the door.

To pause the dryer at any time

Open the door or press PAUSE/CANCEL once.

To restart the dryer

Close the door and press and hold START button until dryer

starts.

NOTE: Drying will continue from where the cycle was interrupted,

if you close the door and press Start within 5 minutes. If the cycle

is interrupted for more than 5 minutes, the dryer will shut off.

Select new cycle settings before restarting the dryer.

Temperature

AdjustM_nual

Cycles Only

Temperature settings can be changed only with Manual

Cycles.

Press the WRINKLE SHIELD

feature button if this

option is desired.