Whirlpool YWED9600TU0 사용 및 관리 매뉴얼 - 페이지 10

{카테고리_이름} Whirlpool YWED9600TU0에 대한 사용 및 관리 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Whirlpool YWED9600TU0 48 페이지. Electronic electric dryer

페이지 인쇄

1. Table of Contents

Vent s ystem chart

NOTE: Side andbottom exhaust installations

have a90 ° turn

inside thedryer. Todetermine maximum e xhaust length, add one

90 °turn tothechart,

Number of Type of

Boxor

Angled

g0 °turns

vent

Iouvered

hoods

or elbows

hoods

Rigid metal

64ft (20m)

58ft (17.7 m)

Flexible m etal 36ft (11m)

28ft (8,5 m)

Rigid metal

54ft (16.5 m) 48ft (14,6 m)

Flexible m etal 31ft (9,4 m)

23ft (7m)

Rigid metal

44ft (13,4 m) 38ft (11,6 m)

Flexible m etal 27ft (8,2 m)

19ft (5.8 m)

Rigid metal

35ft (10.7 m) 29ft (8.8 m)

Flexible m etal 25ft (7,6 m)

17ft (5.2 m)

Rigid metal

27ft (8,2 m)

21ft (6.4 m)

Flexible m etal 23ft (7m)

15ft (4.6 m)

4. Screw thelegs intothelegholes byhand. U se awrench t o

finish turning t helegs until t hediamond marking i snolonger

visible.

5. Place acarton corner p ost f rom dryer p ackaging under e ach

ofthe2 dryer b ack corners. Stand thedryer u p.Slide the

dryer o nthecorner p osts until i tisclose toitsfinal l ocation.

Leave e nough r oom toconnect theexhaust vent.

1. Using a 4"(10.2 cm) c lamp, connect vent t oexhaust outlet i n

dryer. Ifconnecting toexisting v ent, m ake sure thevent i s

clean. The dryer v ent m ust f itover t hedryer e xhaust outlet

andinside theexhaust hood. Check t hatthevent i ssecured

toexhaust hood witha4"(10.2 cm) c lamp.

2. Move dryer i ntoitsfinal l ocation. Donotcrush orkink vent.

3. (On gas models) Check that there are no kinks in the flexible

gas line.

4. Once the exhaust vent connection is made, remove the

corner posts and cardboard.

1. Install exhaust hood. Use caulking compound to seal exterior

wall opening around exhaust hood.

2. Connect vent to exhaust hood. Vent must fit inside exhaust

hood. Secure vent to exhaust hood with 4" (10.2 cm) clamp.

3. Run vent to dryer location. Use the straightest path possible.

See "Determine vent path" in "Plan Vent System." Avoid 90 °

turns. Use clamps to seal all joints. Do not use duct tape,

screws or other fastening devices that extend into the interior

of the vent to secure vent.

Excessive Weight Hazard

Use two or more people to move and install dryer.

Failure to do so can result in back or other injury.

1. To protect the floor, use a large flat piece of cardboard from

the dryer carton. Place cardboard under the entire back edge

of the dryer.

2. Firmly grasp the body of the dryer (not the console panel).

Gently lay the dryer on the cardboard.

See illustration.

The dryer must be connected to the cold water faucet using the

new inlet hoses. Do not use old hoses.

1. Turn cold water faucet off and remove washer inlet hose.

2. Remove old rubber washer from inlet hose and replace with

new rubber washer provided. If space permits, attach the

brass female end of the "Y" connector to the cold water

faucet.

NOTE: If "Y" connector can be attached directly to cold water

faucet, go to Step 6. If "Y" connector cannot be attached

directly to the cold water faucet, the short hose must be

used. Continue with Step 3.

3. Attach short hose to cold water faucet. Screw on coupling by

hand until it is seated on faucet.

4. Using pliers, tighten the couplings with an additional two-

thirds turn.

NOTE: Do not overtighten.

Damage to the coupling can

result.

5. Attach "Y" connector to brass male end of small hose. Screw

on coupling by hand until it is seated on connector.

6. Attach straight end of long hose to "Y" connector.

7. Attach washer cold inlet hose to other end of "Y" connector.

Screw on coupling by hand until it is seated on connector.

Examine the leveling legs. Find the diamond marking.