Before you start...
Read Electrical and Carpentry instructions.
Proper installation is your responsibility. A qualified
technician
should install this range. Make sure you
have everything necessary for correct installation.
It is the customer's responsibility to make sure that
the countertop
has been properly prepared, and
to contact
a qualified electrical installer to assure
that electrical installation is correct.
width - 30"
Front - 29-518"
Top of countertop
Note: countertop
must be level
across front and
I
718" min.
locate
electriial
supply junction
box on cutout
floor or on rear
wall (shown)
near floor line.
required
between
cutout
and
I
36"
countertop
height
Front view of
cabinet cutout
Countertop preparation:
Front edges: You may need to shave
or cut the trim of formed or metal
front-edged
countertops
to clear the
30" width of cook-top.
to clear step of
t+
**For minimum
clearances
to the
top of cooktop
Side view of
cabinet cutout
"Note:
30" min. clearance
between
the top of
cooktop
and the bottom
of an unprotected
wood
or metal cabinet.
24" min. clearance
if protected
by not less than
l/4" flame retardant
millboard
covered
with not
less than No. 28MSG sheet steel. ,015" stainless
steel, or .024" aluminum
or .020" copper.
required
on both
rear corners
of
countertop
cutout.
3280 (formerly the Feaerar stanaara ror
Mobile Home Construction
and Safety, Title
24, HUD Part 280); or when such standard is
not applicable,
the Standard for
Manufactured
Home Installations 1982
(Manufactured
Home Sites, Communities
and Setups), ANSI A225 l-1 987, or with
local codes.
When this range is installed in a mobile
home, it must be secured to the cabinet
(see Step 7) during transit. Any method of
securing the range is adequate
as long as
it conforms to the standards listed above.
Four-wire power supply cord must be used
in a mobile home installation. The
appliance
wiring will need to be revised.
See Electrical requirements, Figure 3,
Panel B.
Top view of
Copies of the standards listed may be
cabinet cutout
obtained
from:
Grounded electrical
outlet is required. See
Electrical requirements.
Cabinet opening dimensions that are
shown must be used. Given dimensions are
minimum clearances
and provide required
0" clearance.
Important: Observe all governing codes
and ordinances.
Electrical Shock Hazard
It is the customer's responsibility:
l
To contact a qualified electrical
installer.
l
To assure that the electrical
installation
is adequate
and in conformance
with
National Electrical Code, ANSVNFPA
70 - latest edition*, and all local
codes and ordinances.
Failure to do so could result in electrical
shock or other personal injury.
Personal Injury Hazard
To eliminate the risk of burns or fire,
avoid installing cabinet storage above
the cooking surface. If cabinets are
already installed, reduce the hazard of
reaching over a heated cooking surface
by installing a range hood.
The range hood should extend a
minimum of 5 inches out from the
bottom front of the cabinets.
Reaching over a heated cooking
surface could result in a serious burn.
* National Fire Protection Association
Batterymarch
Park
Quincy, Massachusetts 02269
Tools needed for
installation:
Electrical
requirements
l/2" dia.
router bit
Electrical Shock Hazard
l
Electrical ground is required on this
appliance.
1
l
Do Not ground to a gas pipe.
l
Do Not have a fuse in the neutral or
grounding circuit. A fuse in the
neutral or grounding
circuit could
result in an electrical
shock.
l
Check with a qualified electrician
if
you are in doubt as to whether the
appliance
is properly grounded.
Failure to follow these instructions
could result in serious injury or death.
If codes permit and a separate grounding
wire is used, it is recommended
that a
qualified electrician
determine that the
grounding path is adequate.
A
w A three-wire or four-wire, single
phase, 120/240-volt, 60 Hz, AC only
electrical supply (or three-wire or four-
wire 120/208-volt if specified on the
serial/rating
plate) is required on a
separate circuit, fused on both sides of
the line. A time-delay
fuse or circuit
breaker is recommended.
The fuse size
must not exceed the circuit rating of the
appliance
as specified on the
serial/rating
plate. The serial/rating plate
is located on the frame behind the oven
door.
B
n
THE RANGE MUST BE CONNECTED
WITH COPPER WIRE ONLY.
b
n
Wire sizes and connections
must
conform to the requirements of the
National Electrical Code, ANSI/NFPA
70 - latest edition* and all local codes
and ordinances for the kilowatt rating of
the range.
D
w The appliance
should be
connected
directly to the fused
disconnect
or circuit breaker box through
flexible, armored or non-metallic
sheathed cable (with copper grounding
wire).
E
n
The flexible armored cable
extending
from the applaince
should be
connected
directly to the junction box.
Locate the junction box to allow two to
three of slack in the cable between the
junction box and the appliance
so that
the range can be moved if servicing is
ever necessary. Do Not cut the conduit.
F
n
A U.L.-listed conduit connector
must
be provided at each end of the power
supply cable (at the appliance
and at
the junction box).
G
n
A wiring diagram is located in the
Tech Sheet. A Tech Sheet is located
behind the lower air grille.
Panel A
페이지 인쇄