D
Provide a gas supply line of
.
3/4" rigid pipe to the range
location.
A smaller size pipe on long
runs may resutt in insufficient gas
supply. Pipe-jolnt compounds,
resistant to the action of L.P. gas.
must be used. With L.P. gas, piping or
tubina she con be l/2' minimum.
L.P. gas suppliers determine
the size
and materials used on the system.
Electrkal
reauirements
Now start...
With range In kitchen.
1
Remove racks and other
, parts from inside ovens.
ampere,
fused electricai
supply
is required. A time-delay
fuse or
circuit breaker is recommended.
It is
recommended
that a separate
circuit serving only this appliance
be
provided.
E
If local codes and
.
ordinances
permit, A.G.A.-
approved.
flexible metal tubing is
recommended
for connecting
this
range to the gas supply line. Do Not
kink or damaae
the flexible tubina
2
Place one foot on the
shipping base. Tilt range
foiard
slightly to free rear legs.
Gently lower range to floor. TiR range
backwards
until front legs are free.
A wiring diagram
is included
in these
instructions.
The wiring diagram
is
also located
on the back of the
range.
when mOVinQ"the range.
A l/2' -
male pipe thread is needed
for
connection
to pressure regulator
female pioe threads.
WARNING: AN EXlENSlON CORD
SHOULD NOT BE USED WiTH THIS
APPLIANCE. SUCH USE hlAY RESULT IN
A FIRE. ELECTRICAL SHOCK, OR OTHER
PERSONAL INJURY.
Recommended
grounding method
3
Remove shipping materials.
.
tape and protective
film from
range.
DO not remove cardboard
shipping base at this time.
DO NOT, UNDER ANY
CIRCUMSTANCES, REMOVE THE
POWER SUPPLY CORD GROUNDING
PRONG.
For your personal safety. this
appliance
must be grounded.
This
appliance
is equipped
with a
J-prong grounding
plug. To minimize
possible shock hazard, the cord must
be plugged
into a mating J-prong.
grounding-type
Wall reCeptOCfe.
grounded
in accordance
with the
National
Electrical Code, ANSI/NFPA
70-1987' and local codes ond ordi-
nances.
See Figure 1. If a mating
wall receptacle
is not avorlable,
it is
the personal responsibility and
obligation
of the customer to hove a
propeflv arounded.
F
The supply line shall be
.
equipped
with a shutoff
valve.
This valve should be located
in the some room as the range and
should be in a location that allows
ease of opening
and closing.
Do Not
block access to shutoff valve.
If ngid pipe is used as a gas
n
supply line, a combination
of
4
Adjust the leveling legs to a
point where the range base
do:
not touch the floor.
5
Plug the electrical
cord into
.
the grounded
outlet.
pipe fittings must be used to obtain
an in-line connection
to the ranae.
All strains must be removed
fromthe
supply and fuel lines so range
will be level and in line.
H
The inlet pressure to the
H regulator should be as follows
for both the operation
and checking
regulator setting:
NATURAL GAS:
Minimum
pressure 6 inches
Maximum
pessure
14 inches
L.P. GAS:
Minimum
pressure 11 inches
Maximum
pressure 14 inches
I .
Line Pressure Testing.
Testing above
l/2 lb psi (gauge)
The range and its individual
shutoff
valve must be disconnected
from
the gas supply piping system during
any pressure testina of that
system at test pressures greater than
l/2 psig (3.5 kPa).
Testing al l/2 lb psi (gauge)
The range must be isolated from the
gas supply piping system by
closing its individual
manual shutoff
valve during any pressure
testing of the gas supply piping
system at test pressures equal to or
less than l/2 psig (3.5 kPo).
electrician.
6
Move the range closer to
cabinet
opening.
Remove
cardboard
shipping piece from
under range.
Move range into
cabinet
opening
and center.
If changrng
and properly grounding
the wall receptacle
is impossible
and where local codes permit
(consult your electrrcal inspector).
a
temporary
adapter
may be plugged
into the existing 2-prong wall
receptacle
to mote with the J-prong
power supplv_cord.
See Figure 2.
7
It is recommended
that this
.
gas range be secured to the
wall or floor. If installing this range in
a mobile home, you MUST secure the
range to the floor. Any method
of
securing the range Is adequate
as
long as it conforms to the standards
listed in Mobile home installation
instructions, Panel A.
%
?
rounded
asambty
electrlcdy grounded
attached
to grounded
metal
cold
water
pipe
metal
cold
water
pipe')
' Gr&ded
cold water pipe must
have metal continuity
to electrical
ground and not be interrupted
by
Place rack in lower
oven.
Place level
on rack, first side to side, then
front to back.
If the range is not
level. remove the storage drawer:
then odjust the legs up or down as
needed.
Note: Oven must be level
for satisfactov
baking conditions.
If
range is secured to the floor, washers
can be added
to level the range.
Tighten screws that secure range to
wo!I or floor
plasticrubber
or other electri
insulatina connectors
such OS 6oses. fittings.
washers or gaskets
(includrng water meter
or pump). Any electrical
insulating connector
should be jumped as
shown with a length of
No. 4 wire securely
clamped
to bare
metal ot both ends
PANEL B
페이지 인쇄