Whirlpool 30" AND 36" (76.2 AND 91.4 CM) WALL-MOUNTCANOPY RANGE HOOD 설치 지침 및 사용 및 관리 매뉴얼 - 페이지 4

{카테고리_이름} Whirlpool 30" AND 36" (76.2 AND 91.4 CM) WALL-MOUNTCANOPY RANGE HOOD에 대한 설치 지침 및 사용 및 관리 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Whirlpool 30" AND 36" (76.2 AND 91.4 CM) WALL-MOUNTCANOPY RANGE HOOD 28 페이지. 30" and 36" (76.2 and 91.4 cm) wall-mount canopy range hood
Whirlpool 30" AND 36" (76.2 AND 91.4 CM) WALL-MOUNTCANOPY RANGE HOOD에 대해서도 마찬가지입니다: 설치 지침 매뉴얼 (28 페이지)

페이지 인쇄

For Non-Vented (Recirculating) Installations, You Will Also

Need:

■

Recirculation Kit Part Number W10294733 for non-vented

(recirculating) installations only. See "Assistance or Service"

section to order.

■

6" (15.2 cm) diameter round metal vent duct - length required

is determined by ceiling height.

Parts Supplied

Remove parts from packages. Check that all parts are included.

■

Hood canopy assembly with blower, lights and canopy glass

already installed.

■

Vent transition with back draft dampers installed

■

Metal grease filter

■

Vent cover support bracket

■

Mounting template

■

2-piece vent cover

■

4 - 4.2 x 8 mm screws

■

6 - 5 x 45 mm mounting screws

■

2 - 3.5 x 9.5 mm mounting screws

■

2 - 8 x 40 mm wall anchors

■

4 - 10 x 60 mm wall anchors

■

4 - 5.4 x 75 mm screws (for 10 x 60 mm wall anchors)

■

T10 Torx

®†

adapter

■

T20

®†

Torx

adapter

Location Requirements

IMPORTANT: Observe all governing codes and ordinances.

Have a qualified technician install the range hood. It is the

installer's responsibility to comply with installation clearances

specified on the model/serial/rating plate. The model/serial/rating

plate is located behind the left filter on the rear wall of the vent

hood.

Canopy hood location should be away from strong draft

areas, such as windows, doors and strong heating vents.

Cabinet opening dimensions that are shown must be used.

Given dimensions provide minimum clearance.

This range hood is recommended for use with cooktops with

a maximum total rating of 60,000 BTUs or less.

Grounded electrical outlet is required. See "Electrical

Requirements" section.

The canopy hood is factory set for venting through the roof or

wall. For non-vented (recirculating) installation see "For non-

vented (recirculating) installation only" in the "Connect Vent

System" section. Recirculation Kit Part Number W10294733

is available from your dealer or an authorized parts distributor.

All openings in ceiling and wall where canopy hood will be

installed must be sealed.

For Mobile Home Installations

The installation of this range hood must conform to the

Manufactured Home Construction Safety Standards, Title 24

CFR, Part 328 (formerly the Federal Standard for Mobile Home

Construction and Safety, Title 24, HUD, Part 280) or when such

standard is not applicable, the standard for Manufactured Home

Installation 1982 (Manufactured Home Sites, Communities and

Setups) ANSI A225.1/NFPA 501A, or latest edition, or with local

codes.

†®TORX and T20 are registered trademarks of Acument Intellectual Properties, LLC.

17³⁄₁₆" (43.7 cm)

Product Dimensions

10⁷⁄₈"

(27.6 cm)

20"

(50.8 cm)

*For non-vented (recirculating) installations

**For vented installations

Cabinet Dimensions

10" (25.4 cm) min.

13" (33.0 cm) max.

9¹⁄₂" (24.1 cm)

10" (25.4 cm) min.

13" (33.0 cm) max.

Side

cabinet

30" (76.2 cm) or

36" (91.4 cm)

"X"

bottom of

canopy

to cooking

surface

*For non-vented (recirculating) installations

**27¹⁄₈" (68.9 cm) min.

**41¹⁄₈" (104.5 cm) max.

*27¹⁄₈" (68.9 cm) min.

*45¹⁄₂" (115.6 cm) max.

13³⁄₁₆"

(33.5 cm)

30" (76.2 cm) or

36" (91.4 cm)

2" (5.1 cm) min.

9" (22.9 cm) min.*

Vent and power

supply cable

entry location

20" (50.8 cm)* min.

Side

cabinet

Centerline

Cooking surface