Whirlpool 36" (91.4 CM) GAS BUILT-IN COOKTOP 설치 지침 및 사용 및 관리 설명서 - 페이지 6

{카테고리_이름} Whirlpool 36" (91.4 CM) GAS BUILT-IN COOKTOP에 대한 설치 지침 및 사용 및 관리 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Whirlpool 36" (91.4 CM) GAS BUILT-IN COOKTOP 28 페이지. 36" (91.4 cm) island-mount canopy range hood
Whirlpool 36" (91.4 CM) GAS BUILT-IN COOKTOP에 대해서도 마찬가지입니다: 설치 지침 매뉴얼 (16 페이지), 사용 및 관리 매뉴얼 (32 페이지)

페이지 인쇄

Electrical Requirements

WARNING

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before operating.

Failure to do so can result in death or electrical shock.

IMPORTANT: The hood must be electrically grounded in

accordance with local codes and ordinances, or in the absence of

local codes, with the National Electrical Code, ANSI/NFPA 70,

latest edition, or Canadian Electrical Code, CSA C22.1.

If codes permit and a separate ground wire is used, it is

recommended that a qualified electrical installer determine that

the ground path is adequate.

A copy of the above code standards can be obtained from:

National Fire Protection Association

One Batterymarch Park, Quincy, MA 02269

CSA International

8501 East Pleasant Valley Road

Cleveland, Ohio 44131-5575

Prepare Location

■ Do not cut a joist or stud unless absolutely necessary. If a

joist or stud must be cut, then a supporting frame must be

constructed.

■ Before making cutouts, make sure there is proper clearance

within the ceiling or wall for exhaust vent.

■ Hood installation height above cooktop is the user's

preference. The lower the hood above the cooktop, the more

efficient the capturing of cooking odors, grease and smoke.

■ Check your ceiling height and the hood height maximum

before you select your hood.

WARNING

Excessive Weight Hazard

Use two or more people to move and install range.

Failure to do so can result in back or other injury.

1. If possible, disconnect and move freestanding or slide-in

range from cabinet opening to provide easier access to

rear wall. Otherwise put a thick, protective covering over

countertop, cooktop or range to protect from damage or dirt.

INSTALLATION INSTRUCTIONS

■ A 120-volt, 60-Hz, AC-only, 15-amp, fused electrical circuit is

required. A time-delay fuse or circuit breaker is also

recommended. It is recommended that a separate circuit

serving only this hood be provided.

■ Do not ground to a gas pipe.

■ Check with a qualified electrician if you are not sure range

hood is properly grounded.

■ Do not have a fuse in the neutral or ground circuit.

■ The range hood must be connected with copper wire only.

■ The range hood should be connected directly to the fused

disconnect (or circuit breaker) box through flexible armored

cable or flexible metallic conduit.

■ Wire sizes must conform to the requirements of the National

Electrical Code, ANSI/NFPA 70, latest edition, or CSA

Standard C22.1-94, Canadian Electrical Code, Part 1 and

C22.2 No. 0-M91, latest edition, and all local codes and

ordinances.

2. Select a flat surface for assembling the unit. Cover that

surface with a protective covering.

3. Determine and mark the centerline on the wall where the

canopy hood will be installed.

4. Select a mounting height, minimum 30" (76.2 cm), above the

cooking surface and mark reference line on the wall.

5. Tape template in place, aligning the template centerline and

bottom of template with hood bottom line and with the

centerline marked on the wall.

A. Centerline

B. Lower support bracket

C. Mounting height reference

D. Fastener locations