Whirlpool 761883306 설치 지침 매뉴얼 - 페이지 2

{카테고리_이름} Whirlpool 761883306에 대한 설치 지침 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Whirlpool 761883306 7 페이지. 30/36" convertible range hood

페이지 인쇄

Before you start...

Proper installation

is your responsibility.

Make sure you have everything

necessary

for correct

installation.

It is the responsibility

of the installer to comply

with the

clearances

specified.

Check the location

where the range hood

will be installed

The location

should be

away from strong draft areas, such as

windows,

doors, and strong heating

vents.

30" model:

29-7/8"

knockout

for

Grounded

electric

\'l-318"

mounting

holes

outlet is required.

See "Electrical

requirements.

wiring knockouts

Tools and materials

needed for

installation:

Electrical

requirements

I -3

compass

or 7"

circle

template

(not shown)

flu

protective

eyeglasses

l-1/4"

drill bit v

Mobile

home installation

The installation

of this range hood must

conform

to the Manufactured

Home

Construction

and Safety Standard,

Title 24

CFR, Part 3280 [formerly

the Federal

Standard

for Mobile

Home Construction

and Safety, Title 24, HUD, (Part 280)) or when

such standard

is not applicable,

the

Standard

for Manufactured

Home

Installations,

ANSI A225 1 and Manufactured

Home Installations,

Sites, and Communities

ANSVNFPA 501 A, or with local codes,

To connect

to four-wire

power supply, the

appliance

wiring must be revised. See

"Electrical

requirements."

Failure to follow these instructions

could

result in death or serious

injury.

If codes permit and a separate

grounding

wire is used, it is recommended

that a

qualified

electrician

determine

that the

grounding

path is adequate.

Electrical

Shock Hazard

Electrical

ground

is required

on this range

hood.

Do Not ground to a gas pipe.

Take special care when drilling

holes into

the wall. Electrical

wires may be concealed

behind the wall covering

and contact

with

them could result in electrical

shock.

Locate any electrical

circuits

that could be

affected

by the installation

of range hood

and disconnect

power circuit.

Do Not have a fuse in the neutral or

grounding

circuit.

A fuse in the neutral or

grounding

circuit

could result in an

electrical

shock.

Check with a qualified

electrician

if you

are not sure range hood is properly

grounded.

Electrical

Shock Hazard

It is the customer's

responsibility:

To contact

a qualified

electrical

installer.

To assure that the electrical

installation

is adequate

and in

conformance

with National

Electrical

Code, ANSVNFPA 70 -

latest edition*,

and all local codes and ordinances.

Installation

work and electrical

wiring

must be done by a qualified

person(s)

accordance

with all applicable

codes and

standards,

including

fire-rated

construction.

Sufficient

air is needed for proper

combustion

and exhausting

of gases

through

the flue (chimney)

of fuel burning

equipment

to prevent

back drafting.

Follow the heating

equipment

manufacturer's

guideline

and safety

standards

such as those published

by the

National Fire Protection

Association

:NFPA), and the American

Society for

Heating, Refrigeration

and Air

Conditioning

Engineers

(ASHRAE),

and

:he local code authorities.

When cutting

or drilling

into wall or

:eiling,

Do Not damage electrical

wiring

and other hidden

utilities.

ilent ducted range hoods to the outdoors.

IO Not end duct inside the building.

-ailure to follow these instructions

could

,esult in death or serious

injury.

Injury Hazard

?eaching

over a heated cooking

surface

should be avoided

to prevent

being

turned. The range hood should

extend a

ninimum

of 5 inches out from the

Bottom of the cabinet.

qeaching over a heated cooking

surface

:ould result in a serious

burn.

Important:

Observe

all governing

codes

and ordinances.

WA 115volt,

60-Hz, AC-only,

fused

electrical

supply is required.

The total

ampere

load used, including

the range

hood, must not exceed

90% of the rated

capacity

of the circuit. The ampere

rating

of the range hood is located

on the

model/serial

rating plate located

on the

side cover the motor housing.

It is the personal

responsibility

and

obligation

of the customer

to contact

qualified

electrician

to assure that the

electrical

installation

is adequate

and in

conformance

with the National

Electrical

Code ANSVNFPA 70 - latest edition*

and

all local codes and ordinances.

W The range hood must be

connected

with copper

wire only.

WThe range hood should be

connected

directly

to the fused disconnect

(or circuit

breaker)

box through

flexible

armored

or nonmetallic

sheathed

copper

cable.

A U.L.-listed strain relief must be

provided

at each end of the power supply

cable.

Wire sizes (COPPER WIRE ONLY) and

connections

must conform

with the rating

of the appliance

as specified

on the

model/serial

rating plate.

Wire sizes must conform

to the requirements

of the National

Electrical

Code ANSI/NFPA

70 - latest edition*,

and all local codes

and ordinances.

Copies

of standards

listed may be obtained

from:

National

Fire Protection

Association

Batterymarch

Park

Quincy,

Massachuseits

02269

Panel A