Whirlpool GZ9730XSS0 사용 및 관리 매뉴얼 - 페이지 4
{카테고리_이름} Whirlpool GZ9730XSS0에 대한 사용 및 관리 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Whirlpool GZ9730XSS0 32 페이지. 30/36" (76.2/91.4 cm) wall mount canopy range hood installation instructions
Whirlpool GZ9730XSS0에 대해서도 마찬가지입니다: 후드 부품 (1 페이지)
페이지 인쇄INSTALLATION REQUIREMENTS
Gather the required tools and parts before starting installation.
Read and follow the instructions
provided with any tools listed
here.
Tools needed
•
Level
•
Drill
•
%6" (8 mm) drill bits for pilot holes
•
%2" (4 mm) drill bits
•
Pencil
•
Tape measure or ruler
•
Caulking gun and weatherproof
caulking compound
•
Phillips screwdriver
•
Vent clamps
•
Metal snips
For vented installations,
you will also need:
•
1 wall or roof cap
•
Metal vent system
For non-vented
(recirculation}
installations,
you will also
need:
•
Charcoal Filter Kit Part Number 8212566
See "Assistance
or Service" section to order.
•
5" (12.7 cm) diameter expandable/flexible
aluminum duct
•
Vent clamps for a 6" (15.2 cm) diameter duct
Parts supplied
Remove parts from packages. Check that all parts are included.
•
Literature package
•
Decorative flue assembly
•
2 metal grease filters for 30" (76.2 cm) models
3 metal grease filters for 36" (91.4 cm) models
•
Parts bag containing:
•
Damper
•
Mounting bracket
•
Flue mounting bracket
•
8 drywall anchors
•
8 - 4.8 x 38 mm pan head mounting screws
•
6- 3.9 x 9.5 mm pan head screws
•
2 - 3.9 x 5.7 mm flat head screws
IMPORTANT: Observe all governing codes and ordinances.
It is the installer's responsibility
to comply with installation
clearances specified on the model/serial rating plate. The model/
serial rating plate is located behind the left filter on the rear wall of
the vent hood.
Canopy hood location should be away from strong draft areas,
such as windows, doors and strong heating vents.
Cabinet opening dimensions that are shown must be used. Given
dimensions
provide minimum clearance. Consult the cooktop/
range manufacturer
installation instructions
before making any
cutouts.
Grounded electrical outlet is required. See "Electrical
Requirements"
section.
The canopy hood is factory set for venting through the roof or
wall. For non-vented
(recirculating)
Installation see "Non-vented
(recirculating)
Installations" in "Prepare Location" section.
Charcoal Filter Kit Part Number 4393848 is available from your
dealer or an authorized parts distributor.
All openings in ceiling and wall where canopy hood will be
installed must be sealed.
For Mobile
Home Installations
The installation of this range hood must conform to the
Manufactured
Home Construction
Safety Standards, Title 24
CFR, Part 328 (formerly the Federal Standard for Mobile Home
Construction
and Safety, Title 24, HUD, Part 280) or when such
standard is not applicable, the standard for Manufactured
Home
Installation 1982 (Manufactured
Home Sites, Communities
and
Setups) ANSI A225.1/NFPA 501A*, or latest edition, or with local
codes.
Product Dimensions
101%6,,
81¾_"
(27.8
cm)
(25.2
cm)
30"
(76.2
cm)
or
36"
(91.4
cm)
(49.8 cm)