Whirlpool KPEU722MSS 사용 및 관리 매뉴얼 - 페이지 4
{카테고리_이름} Whirlpool KPEU722MSS에 대한 사용 및 관리 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Whirlpool KPEU722MSS 10 페이지. 36/48" (91.4/121.9 cm) hood liner installation instructions
페이지 인쇄
Whirlpool
- CIC
8/16/04
2:25
PM
PAGE
1/21
RightFax
For easier installation, it is
recommended that both the
120-volt supply wiring to be
connected to the hood liner wiring
box and the exterior blower
system be instal[ed first. Pull
enough wiring through the wall to
allow for making the electrical
connections at the hood liner
wiring box. Label which cable is
the 120-volt supply wire and
which is the exterior blower cable.
Cover countertop or cooking
surface with a thick, protective
covering to prevent damaging
them.
2-3/4"
5-15/16"
{7.0 ore)
(1511 cm)
l
i
\ I\
i\ \ \ \ \ \ \_
_
\ \i\ \
\ \
O 4,
i
i
i
................
-I ............
I...............
7"
17-5/16"
11" (2Z9cm)
5/16"(7.9mm)
(40.0cm)
dia.
dfa.4-holes
hood size
A
B
36" (91,4cm)
31-7/16"
15-23/32"
(79.9cm)
(39.9cm)
48" (121.9cm)
43-7/16"
21-23/32"
(110.3cm)
(55.2cm)
= Markthe Iocationsof four
5/16" (7.9 ram) dia. holes and an 11"
(27.9 cm) dia. hole as shown. Use a
compass or template and mark the
outline of the 11" (27.9 cm) hole.
= Drill the four holes and, using a
saber saw or keyhole saw, cut the
11" (27.9 cm) dia. hole.
2 _
hood
14-3/16"
(5.1ore)
oooo ,E--h-
onwall
= Drilla 1-1/4" (3.0 cm) dia. hole
at location shown for electrical
wiring.
. Remove the electrical
knockout from the hood liner.
= Remove the filters. Use two
hands to remove filter. Push tab
back to release the lockingpin, pull
down and forward. Set filter aside.
Repeat with other filter(s).
. Remove the wiring box cover
located behind the right handfilter.
= Install U.L.- orC.S.A.- listed
strain relief in hood liner so that
screwscan be tightened,
Electrical
connection
Electrical Shock H==,ard
Disconnect power before
servicing.
Connect ground wire to green
ground screw in terminal box,
Failure to do so can result in
death or electrical shock.
. Disconnect power.
= If not previouslydone, run the
120-volt supply wiringto the hood
lineraccording to electrical codes
and ordinances.
0=
Remove t he four mounting
screwsfrom the parts bag. It is
recommendedthey be placed by
the holes in the hood liner support
for quick access.
Excessive Weight H=ard
Usetwo or more peopleto move
and install hood liner.
Failureto do socan result in back
or other injuw.
I
I
i
I
I
I
1,
While feeding the wiring
through the strain relief, lift the hood
liner into place. Insert the screws
through the support and thread into
the hood liner holes. Tightenscrews
SSCUrely.
2=
Makethe wiring box
electrical connections.