Whirlpool RH8336 SERIES 설치 지침 및 사용 및 관리 설명서 - 페이지 4

{카테고리_이름} Whirlpool RH8336 SERIES에 대한 설치 지침 및 사용 및 관리 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Whirlpool RH8336 SERIES 7 페이지.

페이지 인쇄

Numbers correspond

to steps.

10. 10a.

11. 11a.

5-1/4"

To vent through the roof with

3-1/4" x 10" rectangular vent, mark

a line 1" and 5" from the back wall on the

underside of the cabinet. Mark lines 5-1/4"

to the right and left of the centerline on the

underside of cabinet that connect the lines

just drawn. Use a keyhole saw or saber saw

to cut a rectangular opening for the vent

system. Repeat for the underside of the top

of the cabinet.

To vent through wall with 3-1/4" x 10"

rectangular vent, measure 1/8" and

3-5/8" down from underside of cabinet and

mark on back wall. Measure and mark a

line 5-1/4" to right and left of centerline,

connecting the two lines. Use a keyhole saw

or saber saw to cut a rectangular opening

for the vent system.

To vent through the roof with round vent, a

3-1/4" x 10" to round transition piece must

be used.

Install vent system through the

vent opening in upper cabinet or

wall. Complete venting system according

to method needed. See Venting

requirements. Use caulking to seal exterior

wall or roof opening.

holes

screws

filters

Set range hood on protective

cover. Insert finger into hole in filter

and pull back and down to remove.

Repeat for other filter.

Panel C

7. 8. 9.

cabinet cutouts

Remove light panel and set aside.

wire retainer

indents

wire

retainer

connector plug. Snap blower wire retainer

out of blower housing. Carefully set blower

on protective covering.

Note: It is much easier to remove the vent

knockouts and to install the range hood

with the blower removed.

Venting through

the roof

10.

wiring knockout as needed.

damper blade

(remove if roof cap

has damper blade)

1 1.

Check that the damper blade rotates up

and down freely, if used.

13. 13a.

16. 16a.

12. 12a.

17. 17a.

18. 18a.

Remove three screws that

hold light cover panel in place.

blower wiring

connector plug

remove

screw

Carefully disconnect blower wiring

connector from terminal box

roof vent

knockout

wiring knockout

Remove the roof vent

knockout. Remove top or rear

Attach exhaust vent

connection to range hood.

12.

Remove the screw

holding the terminal

box cover. Remove

cover.

WARNING

Excessive Weight Hazard

Use two or more people to move and

install range hood.

Failure to follow this instruction can

result in back or other injury.

keyhole slot

13.

Lift the range hood into final position and

center. Mark on the underside of cabinet

the location of the four keyhole mounting

slots and the wiring knockout. On some

cabinets, filler blocks may need to be

added for range hood to attach to cabinet.

Set range hood aside on a protected

surface.

14.

Do Not turn on power until

installation is complete. Run

wiring through wall or cabinet according to

the National Electrical Code and local

codes and ordinances.

keyhole slot

outline

15.

Start screws into neck area of

each of the four keyhole

mounting screw slots marked on the

cabinet bottom.

16 .

Lift range hood into position,

and feed electrical wire

through wiring opening. Position the range

hood so that the large end of the keyhole

slots are over the screws. Then push the

range hood toward the wall so that the

screws are in the neck of the keyhole slots.

Tighten mounting screws to cabinet,

making sure mounting screws are in narrow

neck of slots. Make sure that damper blade

rotates up and down freely.

terminal box

17.

Reinstall blower back into

position. Snap blower wire

retainer back into blower housing indents.

Reconnect the blower wiring connector

back into the terminal box connector plug.

screw