Clarion AB243R 소유자 매뉴얼 - 페이지 5
{카테고리_이름} Clarion AB243R에 대한 소유자 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Clarion AB243R 10 페이지. Rds-eon/fm/mw/lw radio cassette combination
Clarion AB243R에 대해서도 마찬가지입니다: 소유자 매뉴얼 (11 페이지)
페이지 인쇄
5. OPERATION
Basic Operations
CAUTION
When this unit is turned on, starting and stop-
ping the engine of a car with its volume raised
to the maximum level may harm your hearing.
Be careful about adjusting the volume.
Turning on the power and adjusting
the volume
1) Press the POWER button 5.
*
To turn the power on and off, press the
button.
2) Turning the Rotary knob 3 clockwise
increases the volume; turning it counterclock-
wise decreases the volume.
The volume level is from 0 (minimum) to 33 (max-
*
imum).
Setting the Z-enhancer
This unit comes with 3 types of sound tone
effects stored in memory. Select the one you
prefer.
The factory default setting is "OFF".
*
Each time you press Z-EHCR button
effect changes in the following order:
"Z-EHCR 1" ➜ "Z-EHCR 2" ➜ "Z-EHCR 3" ➜
"OFF" ➜ "Z-EHCR 1"...
• Z-EHCR 1 : bass emphasized
• Z-EHCR 2 : treble emphasized
• Z-EHCR 3 : bass and treble emphasized
• OFF
: no sound effect
Adjusting the tone
Press A-M button 4 and select the item to
adjust. Each time you press A-M button 4, the
item changes in the following order:
"BASS 0" ➜ "TREB 0" ➜ "BAL 0" ➜ "FAD 0"
➜ Function mode...
6
AB243R/AB243RG
Note:
Be sure to read this chapter by referring to the front diagrams
in chapter 2. CONTROLS on page 3 (unfold).
Adjusting the bass
1. Press A-M button 4 and select "BASS".
2. Turning the Rotary knob 3 clockwise
emphasizes the bass; turning it counterclock-
wise attenuates the bass.
*
The factory default setting is "0". (Adjustment
range: –6 to +6)
3. When the adjustment is complete, press A-M
button 4 several times until the function
mode is reached.
POWER
Adjusting the treble
1. Press A-M button 4 and select "TREB".
2. Turning the Rotary knob 3 clockwise
emphasizes the treble; turning it counter-
clockwise attenuates the treble.
The factory default setting is "0". (Adjustment
*
range: –6 to +6)
3. When the adjustment is complete, press A-M
button 4 several times until the function
mode is reached.
7
Adjusting the balance
, the tone
1. Press A-M button 4 and select "BAL".
2. Turning the Rotary knob 3 clockwise
emphasizes the sound from the right speak-
er; turning it counterclockwise emphasizes
the sound from the left speaker.
The factory default setting is "0". (Adjustment
*
range: L9 to R9)
3. When the adjustment is complete, press A-M
button 4 several times until the function
mode is reached.
Adjusting the fader
1. Press A-M button 4 and select "FAD".
2. Turning the Rotary knob 3 clockwise
emphasizes the sound from the front speak-
ers; turning it counterclockwise emphasizes
the sound from the rear speakers.
*
The factory default setting is "0". (Adjustment
range: F9 to R9)
3. When the adjustment is complete, press A-M
button 4 several times until the function
mode is reached.